Maintenance; General; Daily Cleaning; Replacing Display Light Bulbs - Hatco GRSDH Série Manuel D'installation Et D'utilisation

English

General

Hatco Glo-Ray merchandising Display Warmers are designed
®
for maximum durability and performance with minimum

maintenance.

WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.

Daily Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wipe down the product dividers.
3. Wipe down all exterior and interior surfaces using a water-
dampened cloth. a non-abrasive cleaner may be used for
difficult stains. Hard to reach areas should be cleaned
using small brush and mild soap.
4. Clean the glass side panels using a standard glass cleaner.
5. Clean the plastic sneeze guards and flip-up doors (if
equipped) using soft cleaning cloths, mild soap, and water,
if equipped. NOTICE: Do not use paper towel or glass
cleaner on plastic surfaces — scratching may occur.
Form No. GRSDm-0613

Replacing Display Light Bulbs

Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent light bulb that illuminates
the warming area. The bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF
standards for food holding and display areas.
For 120 and 120/208–240 V applications, use Hatco
P/N 02.30.043.00. For 200, 220, 240, 220–230 and
230–240 V applications, use Hatco P/N 02.30.058.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and
food contamination in the event of breakage.
For 120 and 120/208–240 V applications, use Hatco
P/N 02.30.081.00. For 220, 240, 220–230, and
230–240 V applications use Hatco P/N 02.30.082.00.
ELECTRIC SHOCK HAzARD: Use only Genuine Hatco
Replacement Parts when service is required. Failure to use
Genuine Hatco Replacement Parts will void all warranties
and may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment.

Replacing a Fuse

Use the following procedure to replace a damaged fuse(s).
1. move the Power I/O (on/off) switch(es) to the "O" (off)
position and unplug the power cord. allow the unit to cool.
2. Locate the fuse box on the control side of the unit.
• GRSDS models: Fuses located in the control panel.
• GRSDH models: Fuses located in fuse box on top of
unit.
3. Remove the screws to access fuses.
• GRSDS models: Remove control panel.
• GRSDH models: Remove cover from fuse box.
4. Remove the damaged fuse(s) and replace with new fuse(s).
5. Reverse the above procedure to reassemble.
15
MAINTENANCE
WARNING
WARNING