SCHOLTES CJ 32G W Mode D'emploi page 22

• The hose should not touch objects with sharp edges, corners or moving parts, and it should not be crushed;
• The full length of the hose should be easy to inspect in order to check its condition.
Check that the hose fits firmly into place at the two ends and fix it with clamps complying with current standards. If any of
the above recommendations can not be followed, flexible metal pipes should be used. If the cooker is installed in compliance
with the requirements for class 2, subclass 1, it is highly recommended that the gas connection be made with a flexible
metal pipe in compliance with current safety standards.
Connecting a F Connecting a Fle le le le lexib Connecting a F xib xib xible le le le le, , , , , J J J J Jointless
Connecting a F Connecting a F xib
Remove the hose holder fitted on the appliance. The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
Use only pipes and seals that comply with current National Regulations. The full length of the pipe when installed must not
exceed 2000 mm. After the connection has been made, make sure that the flexible metal pipe does not come into contact
with moveable parts and that it is not crushed.
Chec Chec king the Seal king the Seal
Chec Checking the Seal Chec king the Seal king the Seal
Important: Once the installation has been completed, check to make sure that the seals on all the connections are tight,
using a soapy solution (never a flame).
Connecting the P Connecting the P Connecting the Po o o o o w w w w w er Suppl Connecting the P Connecting the P
Install a normalised plug corresponding to the load indicated on the data plate. When connecting the cable directly to the
mains, install an omnipolar circuit-breaker with a minimum contact opening of 3 mm between the appliance and the mains.
The omnipolar circuit breaker should be sized according to the load and should comply with current regulations (the earth
wire should not be interrupted by the circuit breaker). The supply cable should be positioned so that it does not reach a
temperature of more than 50°C with respect to the room temperature, along its length. Before making the connection,
check that:
• The limiter valve and the home system can support the appliance load (see data plate);
• The mains are properly earthed in compliance with current safety standards and regulations;
• There is easy access to the socket and omnipolar circuit breaker, once the hob has been installed.
N.B.: Never use reducers, adaptors or shunts since they can cause heating or burning.
Con Con Conv v v v v er Con Con er er erting the Cook er ting the Cook ting the Cooker to Dif ting the Cook ting the Cook
In order to convert the cooker for use with a type of gas different than the one for which it was factory set (indicated on the
label attached to the lid), the following steps must be taken:
a) Replace the hose holder mounted on the appliance with that supplied in the bag of "cooker accessories."
Important: The hose holder for liquid gas is marked 8, the hose holder for methane. In any case, always use a new
sealing gasket.
b) Replace the burner nozzles on the hob:
• Remove the grids and slide the burners from their housings;
• Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see
table 1 "Burner and Nozzle Characteristics").
• Replace all the components by repeating the steps in reverse order.
c) Minimum regulation of the hob burners:
• Turn the tap to minimum;
• Remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the flame is small
but steady.
N.B.: In the case of liquid gas, the regulation screw must be screwed in all the way.
• Check that the flame does not go out when you turn the tap quickly from high to low.
d) Regulating the primary air of the burners: The primary air of the burners does not need to be regulated.
R R R R R e e e e e placing the no placing the no placing the no zzles on se zzles on se
placing the nozzles on se placing the no zzles on separ zzles on se
• remove the grids and slide the burners from their housings. The burner consists of 2 separate parts (Fig. E and fig.
F);
• unscrew the burers with a 7 mm wrench spanner. The internal burner has a nozzle, the external burner has two (of
the same size). Replace the nozzle with models suited to the new type of gas (see table 1).
• replace all the components by repeating the steps in reverse order.
ointless, , , , , Stainless Steel Pipe to a ointless ointless Stainless Steel Pipe to a T T T T T hr Stainless Steel Pipe to a Stainless Steel Pipe to a
ointless Stainless Steel Pipe to a
er Supply Cor er Suppl er Suppl er Suppl y Cor y Cor y Cord to the Mains y Cor d to the Mains d to the Mains d to the Mains d to the Mains
er to Dif er to Dif er to Dif er to Diff f f f f er er er erent er ent T T T T T ypes of ent ent ent ypes of Gas ypes of ypes of ypes of
par par para a a a a te "doub te "doub te "doub
par te "double f te "doub
Gas Gas Gas Gas
le f le f lame " b lame " b ur ur ners: s: s: s: s: ner ner
le flame " b le f lame " bur lame " b urner ur ner
- 22 -
hreaded hr hr eaded eaded Attac eaded Attachment Attac Attac hment hment hment
hr eaded Attac hment