How To Use; Overhead Rigging - JB Systems Light LED Pulsar Mode D'emploi

ENGLISH
 The housing and the lenses must be replaced if they are visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don't use the effect in the presence of persons suffering
from epilepsy.
DESCRIPTION:
1. Optical lens with manual focus adjustment
2. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
3. Mains input with IEC socket and integrated fuse holder, connect the supplied mains cable here.
4. ¼" jack used to connect an optional CA-8 controller.
5. Din-5pin input, used to connect an optional wireless receiver, named RF-8R.
6. DIP switches, used to set the DMX-starting address of the unit.
7. DMX input: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller or from another Led Pulsar light effect when used in master/slave
mode.
8. DMX output: 3pin female XLR-connector used to connect the Led Pulsar with the next unit in the DMX
chain or with another Led Micro Scan when used in master/slave mode.
9. Scanning mirror.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
JB SYSTEMS
®
OPERATION MANUAL
3/41 LED PULSAR
ENGLISH
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.

HOW TO USE:

Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
1. Standalone 1unit:
DMX start address MUST be set to 001. (first DIP switch = ON, all other are OFF).
Then just connect the unit to the mains and put on some music. The unit will start working automatically
to the rhythm of the music.
You can use an optional CA-8 controller or wireless RF-8 controller to control some of the automatic
features. See #3 for more information.
2. Two or more units in master/slave setup:
Connect 2 or more units together using good quality balanced XLR microphone cables. The first unit
must have no cable connected to its input and must be set as the master; the others must be set as
slave units and will follow the commands of the Master unit.
Set the DMX addresses as follows:
 Master unit: DMX start address MUST be set to 001. (first DIP switch = ON, all other are OFF)
 Slave units: DMX start address may have any value but NOT 001 (example: set the first 3 DIP
switches to ON)
You can use an optional CA-8 controller or wireless RF-8 controller to control some of the automatic
features. See #3 for more information.
3. Connect an optional CA-8 or RF-8 controller for more control:
The CA-8 or RF-8 controller can only be used in standalone or in master/slave mode:
 CA-8 wired remote: Connect the controller to the jack input of the first unit (master).
 RF-8SET wireless remote: the wireless remote has two parts:
 RF-8T: small RF-transmitter that can control up to 5 effects.
 RF-8R: small RF-receiver that should be connected to the DIN 5pin input of the LED Pulsar.
See the installation manual of the receiver for more information.
Now you can control all the connected units:
Stand by Blackout the unit
1. Synchronous Strobe in white
Function 2. Sound strobe in white
3. Sound Strobe in color
Mode Strobe (LED OFF)
JB SYSTEMS
®
OPERATION MANUAL
Select Show
Select Color
1-6
LED ON LED blinking
4/41 LED PULSAR