Symbols Used In The Manual; Main Machine Components; Purpose And Content Of The Manual; Target Group - Fimap FE A65.2 DP Manuel D'utilisation Et D'entretien

The descriptions contained in this document are not binding. The company therefore reserves the
right to make any modifications at any time to elements, details, or accessory supply, as considered
necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction,
even partial, of the text and drawings contained in this document is prohibited by law.
The company reserves the right to make any technical and/or supply modifications. The images
are shown as reference only and are not binding as to the actual design and/or equipment.

SYMBOLS USED IN THE MANUAL

Open book symbol with an "i":
Indicates the need to consult the instruction manual.
Open book symbol:
Tells the operator to read the manual before using the appliance.
Covered place symbol:
the operations preceded by this symbol must always be carried out in a dry, covered area.
Information symbol:
Indicates additional information for the operator, to improve the use of the device.
Warning symbol:
Carefully read the sections preceded by this symbol meticulously following the instructions
indicated for the safety of the operator and the device.
Symbol indicating the compulsory use of protective gloves:
Indicates that the operator should always wear protective gloves, to avoid the risk of
serious injury to his hands from sharp objects.
Recycling symbol:
Tells the operator to carry out the operations in compliance with environmental regulations
in force in the place where the appliance is being used.
Disposal symbol:
Carefully read the sections marked with this symbol for disposing of the appliance.

MAIN MACHINE COMPONENTS

I componenti principali dell'apparecchio sono:
1. Vacuum nozzle
2. Handling trolley
3. Power cable.
4. Suction filter cleaning solution tank.
5. Collection tank.
6. Vacuum lock float..
7. Vacuum head unlocking hook.
8. Female quick coupling for detergent solution
9. Quick male connection for detergent solution.
10. Spray Pump Control Switch.
11. Main switch.
12. Activation lever Turn off nebulization.
19
7
13
5
2
10
11
16
18
21
13. Handle for handling .
14. Handle bar for vacuum head lifting.
15. Button for releasing the vacuum nozzle catch.
16. Detergent Solution Tank.
17. Cleaning Solution Tank Cap.
18. Drain Tube Collection Drum cap.
19. Vacuum head.
20. Hose Distribution Detergent Solution.
21. Drain Pipe Collection Drum.
22. Spray nozzle.
8
6
17
20
16
3

PURPOSE AND CONTENT OF THE MANUAL

The aim of this manual is to provide customers with all the information needed to use the appliance in
the safest, most appropriate and most autonomous way. It includes information concerning technical
aspects, safety, operation, appliance downtime, maintenance, spare parts and scrapping. Operators
and qualified technicians must read the instructions in this manual carefully before carrying out any
operation on the appliance. If in doubt about the correct interpretation of instructions, contact your
nearest Customer Service Centre to obtain the necessary clarifications.

TARGET GROUP

This manual is aimed at operators and qualified technicians responsible for appliance maintenance.
Operators must not perform operations that should be carried out by qualified technicians. The
manufacturer is not liable for damages resulting from failure to comply with this veto.

STORING THE USE AND MAINTENANCE MANUAL

The Use and Maintenance Manual must be stored in its special pouch close to the appliance,
protected from liquids and anything else that could compromise its legibility.

ON CONSIGNMENT OF THE MACHINE

When the machine is delivered to the customer, an immediate check must be performed to ensure all
the material mentioned in the shipping documents has been received, in addition to verifying that the
equipment has not been damaged during transportation. If this is the case, the carrier must ascertain
the extent of the damage at once, informing our customer service office. It is only by prompt action
of this type that the missing material can be obtained, and compensation for damage successfully
claimed.

INTRODUCTORY COMMENT

Any type of equipment can only work properly and effectively if used correctly and kept in full working
order by performing the maintenance operations described in the attached documentation. You
should therefore read this instruction manual carefully, consulting it again if issues arise while using
the machine. If necessary, remember that our assistance service (organised in collaboration with our
dealers) is always available for advice or direct intervention.

IDENTIFICATION DATA

For technical assistance or to request replacement parts, always give the model, the version and the
serial number (written on the relevant plate).

TECHNICAL DESCRIPTION

The PRO appliances are wet and dry vacuum cleaners that, using the vacuum created inside the
collection tank by the fan driven by electrical motors, can vacuum dust and dry-wet solid bodies, using
accessories in contact with the surface of the floor and furnishings. The vacuum hose channels the air
into the collection tank, where the dust and solid residues are trapped by filters. The appliance must
only be used for this purpose.

INTENDED USE

This appliance is designed and built to be used by a qualified operator to clean (by vacuuming solid,
dry or wet elements) smooth, compact flooring in the commercial, residential and industrial sectors, in
proven safety conditions.
ATTENTION: the appliance is not suitable for use in the rain, or under jets of water.
IT IS FORBIDDEN to use the appliance for picking up dangerous dusts or inflammable liquids
in places with an explosive atmosphere. In addition, it is not suitable as a means of transport
for people or objects.
Operator cooperation is paramount for accident prevention. No accident prevention programme can
be effective without the full cooperation of the person directly responsible for machine operation. The
majority of occupational accidents that happen either in the workplace or whilst moving are caused by
failure to respect the most basic safety rules. An attentive, careful operator is most effective guarantee
against accidents and is fundamental in order to implement any prevention programme.

SERIAL NUMBER PLATE

The serial number plate is located at the rear of the vacuum cleaner, and indicates the general
characteristics of the appliance, in particular the appliance's serial number. The serial number is a very
important piece of information and should always be provided together with any request for assistance
or to purchase spare parts.
30

SAFETY

Serial nr:
SAP code:
Serial nr:
V
W Mod:
W Date:
Hz
Made in EEC