Symbols Used On The Appliance; Preparing The Appliance; How To Unpack The Appliance; How To Transport The Appliance - Fimap FE A65.2 DP Manuel D'utilisation Et D'entretien

Masquer les pouces Voir aussi pour FE A65.2 DP:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

TECHNICAL DATA
Electrical
characteristics
Suction
motor
frequency)
Number of suction motors
Type of suction motor
Number of stages suction motor
Rated Power suction motor/max
Type of suction
Air flow
Vacuum suction
Total Drum Capacity Collection
Useful Capacity Collection Keg
Collection tank Material
Power cord length
Type of Spray pump
Number of spray Pumps
Nebulization pressure (maximum)
Nebulization Range (maximum)
Tank Capacity Solution
Weight of the appliance (without accessories)
Appliance Dimensions (WxDxH)
Diameter accessories
Sound pressure level (ISO 11201)
Incertezza KpA

SYMBOLS USED ON THE APPLIANCE

Main switch symbol:
This is used on the back of the appliance to indicate the main switch.

PREPARING THE APPLIANCE

PREPARING THE APPLIANCE
The appliance is contained in a specific packaging, the packing elements (plastic bags, clips, etc.) as
potential sources of danger must not remain within the reach of children, incapable, etc.
The total mass of the unit with the packaging is 30kg for A 58.3 DP The dimensions of the packaging
are as follows:
A
50cm
B
73cm
C
102cm

HOW TO UNPACK THE APPLIANCE

The procedure for removing the device from its packaging is the following:
1. Open the outer box.
2. Remove the accessories from the box and carefully lay them on the ground.
3. Take out the vacuum head carton.
4. Remove the appliance from the box using the handle, being careful not to damage either during
the operation.
5. Take out the appliance from the protective bag using the relative handle, taking care not to damage
either.
N.B.: it is recommended that all the packaging components be kept for any future transportation
of the appliance.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.

HOW TO TRANSPORT THE APPLIANCE

The procedure for carrying the appliance safely is as follows:
1. Carry out the phases to secure the appliance (read paragraph "Securing the Appliance").
2. Disconnect the male connector (1) of the detergent Solution Distribution Tube (2) from the female
Connector (3) on the suction head (Fig. 1).
3. Remove the suction pipe (4) from the suction nozzle (5) in the collection shaft, press the button (6) to
release the latch (Fig. 2) before pulling the suction pipe.
4. Insert the appliance into the carton being careful not to damage both during this operation.
WARNING: Remember to position the wheels of the appliance at the bottom of the
cardboard, place the latches around the collection frame to avoid any damage during
S.I.
FE A65.2 DP
(voltage-
220-240
V - Hz
50-60
2
By-Pass
2
W
2000/2200
Wet & Dry
m
/h
389
3
kPa
22
l
65
l
47
Acciaio inox
m
10
Pistone
2
kPa
800
m
/h
0.07
3
l
18
Kg
27
cm
49 X 71 X 97
mm
40
dB (A)
72
dB (A)
1.5
5. Insert the accessory support and the head retainer inside the cardboard.
6. Place the accessories inside the cardboard.
7. Close the cardboard.
WARNING: For transport in vehicles, ensure the appliance in accordance with the directives in
force so that it cannot slip and tip over.
PRUDENCE: CAUTION: These operations must be carried out using gloves to protect the hands.
3
5
1
4
2
1
The steps to secure the appliance, thus giving the possibility to carry out operations safely, are identified
as follows:
1. Check that both the general switches (1) are switched off, otherwise take them to the "0" position
(Fig. 1).
2. Check that the plug (2) in the power supply cable (3) is disconnected from the socket (4) of the mains
supply, otherwise disconnect it (Fig. 2).
3. Wrap the power cord under the lifting handle of the appliance.
PRUDENCE: It is advisable to handle the power cord with your hands dry, to avoid serious injury.
PRUDENCE: To prevent damage to the power cord, disconnect the mains plug from the mains
socket by pulling the plug directly instead of the cable.
4
1
2
3
1
INSERT FILTER IN SPONGE (OPTIONAL)
To insert the sponge filter at the bottom of the suction head, carry out the following:
1. Carry out the phases to secure the appliance (READ PARAGRAPH "SECURING THE APPLIANCE").
2. Remove the suction head (1) using the handle above it, before removing the head loosen the
retaining hooks (2) located at the side of the collection shaft (3) (Fig. 1).
WARNING: Before removing the suction cover, remember to unscrew the plug (4) in the solution
tank (Fig. 2).
3. Lay the suction head gently on the floor.
4. Insert the Sponge filter (5) over the float support (6) (Fig. 3).
5. Refit the suction head (1) above the collection frame (4), remember to fix it using the retaining hooks
(3).
NOTABENE: Se si utilizza il filtro in spugna (5) il filtro in stoffa permanente deve essere rimosso.
1
2
3
1
INSERTING NYLON FILTER (OPTIONAL)
To insert the nylon filter inside the collection drum, carry out the following:
1. Carry out the phases to secure the appliance (READ PARAGRAPH "SECURING THE APPLIANCE").
2. Remove the suction head (1) using the handle above it, before removing the head loosen the
retaining hooks (2) located at the side of the collection shaft (3) (Fig. 1).
WARNING: Before removing the suction cover, remember to unscrew the plug (4) in the solution
tank (Fig. 2).
3. Lay the suction head gently on the floor.
4. Inserire all'interno del fusto di raccolta il sacco filtro in nylon (5), per fissarlo farlo aderire al perimetro
dell'imboccatura del fusto stesso (Fig.3).
5. Refit the suction head (1) above the collection frame (4), remember to fix it using the retaining hooks
(3).
1
2
3
1
31
6
2
SAFETY OF THE APPLIANCE
2
PREPARING THE WORK
4
6
5
2
3
4
5
2
3

Publicité

Table des Matières
loading

Table des Matières