Alpine VPE-S431 Mode D'emploi page 3

Feature
This unit is designed to connect to the IVA-D300 series to
expand their functions.
In addition, when this unit is not connected to the IVA-D300
series, it can perform visual effects, switch video output to a
rear monitor connected to this unit, etc.
a Operations can be performed from the IVA-D300 series
when connected. For details, refer to the Owner's
Manual of the IVA-D300 series.
a Operations can be performed from the touch panel
monitor when connected. For details, refer to the
Owner's Manual of the touch panel monitor.
Operation
This unit can be operated by connecting REAR SEL1 and
REAR SEL 2 leads to a push switch (sold separately). For
details, consult an authorized ALPINE dealer.
REAR SEL
1,2 leads
OK
• Use a switch (sold separately) which has an automatic
return function to connect with REAR SEL 1,2 leads.
• When operating with the Monitor Control 1,2 leads,
connect to a switch (sold separately) as well. The
automatic return function is not necessary. (Refer to
"SWITCHING THE REMOTE SENSOR" page 3.)
Switching the Output Source
Video output from AUX OUT 1/2 for each monitor can be
switched.
1
Press the REAR SEL 1 or the REAR SEL 2
switch.
The SOURCE SEL. display appears.
SOURCE SEL.
AUX-1
AUX-2
AUX-3
DVD PLAYER
VISUALIZER
OFF
SETUP
RETURN
REAR SEL 1: The source of the external monitor
connected to the AUX OUT 1.
REAR SEL 2: The source of the external monitor
connected to the AUX OUT 2.
2
-EN
Body of
your car
Push switch, etc.
2
Press the REAR SEL 1 or the REAR SEL 2
switch to select an item from the list below.
AUX-1 → AUX-2 → AUX-3 → DVD PLAYER*
VISUALIZER* 2 → OFF → SETUP → RETURN
1
* Displayed only when the IVA-D300 series are
connected.
2
* Displayed when VISUALIZER is set to other than
OFF.
When the IVA-D300 series are connected, this is
displayed only when VISUALIZER is set to ON in the
IVA-D300 series.
• The AUX NAME set in "SETUP" is displayed for
AUX-1, 2 or 3.
3
Press and hold the REAR SEL 1 or the REAR
SEL 2 switch for more than 2 seconds.
The selected source is displayed on the monitor.
• When RETURN is selected, the display returns to the
one prior to the SOURCE SEL.
SETUP
Each setting can be performed by the procedure shown below.
The setup menu is common for both REAR SEL 1 and
REAR SEL 2.
• When IVA-D300 series is connected, the VISEAL EFFECT,
VISUALIZER and AUX IN-1, 2, 3 NAME cannot be set in
this unit. Set these functions in the IVA-D300 series.
1
Press the REAR SEL 1 or the REAR SEL 2
switch.
The SOURCE SEL. display appears.
2
Press the REAR SEL 1 or the REAR SEL 2
switch to change the setting item. Select
SETUP.
3
Press and hold the REAR SEL 1 or the
REAR SEL 2 switch for more than 2 seconds.
The SETUP display appears.
4
Press the REAR SEL 1 or the REAR SEL 2
switch to select the desired setting item.
VISUAL EFFECT → VISUALIZER →
AUX IN-1,2,3 SIGNAL → AUX IN-1,2,3 NAME
→ RETURN
5
Press and hold the REAR SEL 1 or the
REAR SEL 2 switch for more than 2 seconds
to change the setting.
6
After settings, press the REAR SEL 1 or the
REAR SEL 2 switch to select RETURN, and
press and hold the switch for more than 2
seconds.
The SOURCE SEL. display is restored. To return to
normal mode, select RETURN again, and press
and hold the switch for more than 2 seconds.
Either VISUAL EFFECT or VISUALIZER will start if
set to on.
1
→