Technical Data; Noise/Vibration Information - Bosch GKT 18V-52 GC Professional Notice Originale

22 | English
(45) Slider for guide groove clearance setting (2x)
A)
(46) Parallel guide
(47) Wing bolt for parallel guide (2x)
(48) Screw for fine adjustment 0° mitre/bevel cut
(49) Screw for fine adjustment 45° mitre/bevel cut
(50) Groove for Bosch guide rail
(51) Dust/chip bag
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Plunge circular saw
Article number
Rated voltage
A)
No-load speed
Max. cutting depth
– at a 0° mitre/bevel angle
– at a 45° mitre/bevel angle
Spindle lock
Use with FSN guide rail system
Speed preselection
Constant electronic control
Base plate dimensions
Saw blade diameter
Max. base blade thickness
Min. base blade thickness
Max. tooth thickness/offset
Locating bore
Weight according to
A)
EPTA-Procedure 01:2014
Weight without battery
Recommended ambient tem-
perature during charging
Permitted ambient temperature
B)
during operation and during
storage
Compatible rechargeable bat-
teries
Recommended rechargeable
batteries for maximum per-
formance
Recommended chargers
Data transmission
Bluetooth®
Signal interval
1 609 92A 4XT | (11.02.2020)
A)
A)

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-5.
GKT 18V-52 GC
Typically, the A-weighted noise level of the power tool is:
3 601 FB4 0..
Sound pressure level 96 dB(A); sound power level
V= 18
107 dB(A). Uncertainty K = 3 dB.
-1
min 2800–5500
Wear hearing protection
Vibration total values a
determined according to EN 62841-2-5:
mm 52
Sawing wood: a
mm 32
The vibration level and noise emission value given in these
●
instructions have been measured in accordance with a
●
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
●
estimation of vibration and noise emissions.
●
The stated vibration level and noise emission value repres-
mm 305 x 169
ent the main applications of the power tool. However, if the
mm 140
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
mm 1.4
and noise emission value may differ. This may significantly
mm 1.0
increase the vibration and noise emissions over the total
mm 2.4
working period.
mm 20
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
kg 4.6–5.5
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
kg 4.1
over the total working period.
°C 0 to +35
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
°C –20 to +50 power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
GBA 18V...
ProCORE18V...
u
ProCORE18V...
≥ 5.5 Ah
GAL 18...
Using the Bluetooth ® Low Energy Module
GAX 18...
GCY 42
GAL 36...
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Bluetooth® 4.2
C)
(Low Energy)
s 8
Plunge circular saw
D)
Max. signal range
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) The mobile terminal devices must be compatible with Bluetooth
Low Energy devices (version 4.2) and support the Generic Ac-
cess Profile (GAP).
D) The signal range may vary greatly depending on external condi-
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
(triax vector sum) and uncertainty K
h
2
< 2.5 m/s , K = 1.5 m/s
h
Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
GKT 18V-52 GC
m 30
®
2
Bosch Power Tools