Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
7.2 Selecting the operation mode –
Menu items
–
(15-channel mode)
15 Channel
–
(37-channel mode)
37 Channel
Mast Mode
Selection between:
–
(no output of control signals))
Alone
–
(output of control signals for slave units)
Host
Auto Mode
Selection of 5 programs:
Sound Control
Setting of sound sensitivity:
Manual Control
Available functions:
Pan
,
,
,
Red1
Green1
Blue1
,
,
,
Red2
Green2
Blue2
,
,
,
Red3
Green3
Blue3
,
,
,
Red4
Green4
Blue4
,
,
,
Red5
Green5
Blue5
,
,
,
Red6
Green6
Blue6
Note: In the 15-channel mode, the functions
...
are not available .
Red2
White6
7.3 Basic settings –
Menu items and functions
Reversal of the pan direction
Pan Reverse
Selection between:
No
Pan fine adjustment (for service only)
Pa
Adjust
n
Tilt fine adjustment (for service only)
Tilt Adjust
Pan angle
PanAngle Choose
Selection between:
540
Setting for the display
Display BkLight
Selection between:
Off
button is pressed),
Operating mode when no DMX signal is received
DMX Lost
Selection between:
Blackout
DMX signal is received after the unit was set into operation: LEDs off, moving head in home position; when no DMX signal is received
anymore during operation: the most recent control commands will be kept)
Note: When the menu item
internal control commands will be kept .
Automatic position correction pan / tilt
Encoder
Selection between:
No
Reset (reset of motor control)
Reset
Factory setting (reset of the menu settings, with the exception of the setting for
Default
7.4 Status information –
Menu items and functions
Firmware version (operating system of the unit)
Software Version
Number of operating hours
Operate Time
10
Operate Mode
Functions
Channel mode (= number of DMX channels); for operation with a DMX controller, select the channel
mode according to the functions desired (
Press ENTER to confirm the respective menu item; the channel mode will be set and saved .
Setting for the master / slave mode
In the master / slave mode, multiple CUBE-630 / LED can be operated in sync without a DMX controller (in
the mode
Connect the units in a chain as described in chapter 5 (also see fig . 7), set the master unit to
the slave units to
Note: With the setting
Master unit
➐
Master / slave mode
Automatic mode (automatic show program) for operation without DMX controller;
the menu item
...
Program 00
04
Note: The programs differ in the two channel modes .
Sound mode (music-controlled show program) for operation without DMX controller;
the menu item
...
00
99 %
Manual control for operation without DMX controller, to test a function or to temporarily set the moving
head to a fixed position /colour radiation:
,
,
Tilt
Call up the respective function and set the value (
,
White1
go back, press ENTER or MENU . Proceed in the same way with the next function desired etc . The menu will
,
White2
not be exited and the display will remain switched on as long as one of the functions is selected or called up .
,
White3
When you return to
,
White4
– When
,
White5
exited and all values will be reset .
White6
– When
another operating mode is selected or
Note: Manual control will not be possible when the menu item
been set to
–
System Setting
(function deactivated) and
Yes
(max . pan angle: 540°) and
(display will be switched off after approx . 30 seconds when no button is pressed; the display will be switched on again when a
(display always switched on)
On
(LEDs switched off and moving head in home position),
DMX Lost
(function deactivated) and
Yes
–
Status Info
–
,
or
Auto
Sound
Manual Control
. Set all units to the same channel mode .
Alone
, the channel mode cannot be changed .
Host
Slave unit
DMX
DMX
DMX
output
input
output
(
chapter 7 .3) must be set to
☞
DMX Lost
(
chapter 7 .3) must be set to
☞
DMX Lost
Manual Control
(
chapter 7 .3) has been set to
☞
DMX Lost
has been set to
DMX Lost
Hold
and program 0 is being executed .
Auto
(function activated)
(max . pan angle: 630°)
630
is set to
while the unit is being operated in the automatic mode or sound mode, the most recent
Hold
(function activated)
☞
chapter 8) .
) . A single unit (master) will control the other units (slaves) .
Slave unit
Slave unit
DMX
DMX
DMX
DMX
input
output
input
output
.
Auto
.
Sound
...
); the setting will be instantly carried out . To
000
255
with the button MENU, the unit will behave as follows:
or
Blackout
Auto
: All settings will be kept . The values will be reset as soon as
is called up again .
Manual Control
has been set to
DMX Lost
(automatic mode),
Auto
Sound
Sound Control
and
Host
Slave unit
DMX
DMX
input
output
DMX terminating plug
( if required )
: The operating mode will be
or when it has
Sound
(sound mode),
(when no
Hold
)
Publicité
Table des Matières
