Water Supply And Drain Connections - Hoshizaki FM-170AFE Notice D'utilisation

ENGLISH
your plug, proceed as follows:
The wire which is coloured Green-and-Yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the
symbol or coloured Green or Green-and-
Yellow. The wire which is coloured Blue must
be connected to the terminal which is marked
with the letter N or coloured Black. The wire
which is coloured Brown must be connected to
the terminal which is marked with the letter L or
coloured Red.
* Should the socket outlets in the installation site
not be suitable for the plug supplied with your
product, the plug must be removed (cut off if it is
moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the
power supply cord, it must be disposed of. There
should be no attempt to reuse it. Inserting such
a plug into a socket elsewhere presents a serious
risk of electrical shock.
* The non-rewirable plug must never be used
without a fuse cover being fitted.
The correct replacement for the detachable fuse
cover is identifiable from the manufacturer's
reference number stamped on the plug.
Supply of replacement fuse covers can be
obtained from Hoshizaki Parts/Service Centres.
Fuses should be rated at 0A and approved to
BS 362.
3. WATER SUPPLY AND DRAIN
CONNECTIONS
(For the U.K. only, the connections must be in
accordance with current requirements of the Model
Water Byelaws 986 SI No. 47)
* Only potable water should be used for the
icemaker.
* Water supply pressure should be minimum 0.5
bar and maximum 8 bar. If the pressure exceeds
8 bar, use a proper pressure reducing valve. Do
NOT throttle back the supply tap.
* A plumbing permit and services of a licensed
plumber may be required in some areas.
* The icemaker drain is gravity flow, so ensure
drain pipe has an adequate pitch or fall.
* Water should drain into an open trap.
II. OPERATING INSTRUCTIONS
WARNING
. This icemaker is designed to produce and
store edible ice. To keep the icemaker
hygienic:
* Wa s h y o u r h a n d s b e f o r e r e m o v i n g
ice. Use the Plastic Scoop provided
(accessory).
* The Storage Bin is for ice use only. Do
not store anything else in the Bin.
* Clean the Storage Bin before use (see "III.
. CLEANING").
* Keep the Scoop clean. Clean it by using
a neutral cleaner and rinse thoroughly.
* Close the Door after removing ice to
prevent entrance of dirt, dust or insects
into the Storage Bin.
2. The use of any electrical equipment
i n v o l v e s t h e o b s e r v a n c e o f s o m e
fundamental rules. In particular:
* Instances of high humidity and moisture
increase the risk of electrical short circuits
and potential electrical shocks. If in
doubt, disconnect the icemaker.
* Do not damage the power cord or pull it
in order to disconnect the icemaker from
the feed network.
* Use the attachment plug as the main
power disconnect switch for the icemaker.
* Appliance must be positioned so that the
plug is accessible.
* Do not touch the attachment plug and
other electrical parts or operate the
Power Switch with damp hands.
* T h i s a p p l i a n c e i s n o t s u i t a b l e f o r
unsupervised use by young children or
aged or infirm persons.
* Do not attempt to modify the icemaker.
O n l y q u a l i f i e d p e r s o n n e l m a y
disassemble or repair the appliance.
3. All parts are factory-adjusted. Improper
adjustments may result in failure.
4. If the unit is turned off, wait for at least 3
minutes before restarting the icemaker to
prevent damage to the Compressor.
1. OPERATION
The installer will normally commission the icemaker
to start the automatic icemaking process. To
2