Starting And Stopping - Bosch AQUATAK 150 PRO Instructions D'emploi

F016 L70 375 - GB Seite 4 Montag, 14. November 2005 1:15 13
AQUATAK 160 PRO X
Twist the nozzle sleeve to adjust from a pencil to
J
a fan jet and vice versa.
To apply the detergent move the nozzle from
K
high pressure mode to low pressure mode by pulling
the nozzle forward.
To adjust the spray patten twist the nozzle.
Also refer to Advice on using pressure washer re-
garding the detergent suction rate.
Roto power lance
O Turn the vario-jet/fan power lance 9 90° anti-
clockwise. Extract the vario-jet/fan power lance.
(AQUATAK 150 PRO/150 PRO X)
Unscrew the vario jet-fan power lance 9 from the
power gun 7. (AQUATAK 160 PRO X)
P
Insert the roto-power lance 14 into the power
gun 7. Depress and turn the roto-power lance 90°
clockwise to lock in place. (AQUATAK 150 PRO/
150 PRO X)
Screw the roto-power lance 14 into the power gun 7.
(AQUATAK 160 PRO X)

Starting and Stopping

Starting
Connect the product to the mains supply ensuring
that the mains switch is in the (
Open water tap.
R
Press the safety lock 1 to release the trigger 2.
Fully press the trigger 2 until there is a constant flow
of water to clear the air from the machine and water
supply hose. Release trigger 2. Press the trigger
safety lock.
Turn on main switch 10.
Point the power gun 7 downwards. Press the trigger
safety lock to release the trigger 2. Fully press the
trigger 2.
Stopping
Release trigger 2. Press the trigger safety lock. The
power gun is now locked and cannot be operated ac-
cidentally.
Turn off the main switch 10.
Close water tap. Unplug the machine from the elec-
tric supply.
Press the trigger safety lock 1 to release the trig-
ger 2. Fully press the trigger 2 until there is no more
water pressure in the machine. Release trigger 2.
Press the trigger safety lock 1.
Disconnect water supply hose from machine and
water supply.
16 • F016 L70 375 • TMS • 21.10.05
Advice using pressure washer
General
Ensure that the machine is on level ground.
Do not overreach with the high pressure hose or
move the pressure washer by pulling the hose, this
could cause the machine to become unstable and
fall over.
Do not kink or drive a motor vehicle over the high
pressure hose. Do not expose the high pressure
hose to sharp edges or corners.
Never use the roto nozzle to clean motor vehicles.
Operating with Detergents
Only use Bosch approved detergents. Unsuita-
ble detergents may damage the unit and the ob-
ject being cleaned.
M N
/
lute as recommended. The tank(s) can be removed
to aid filling and emptying.
/
I K
lance to low pressure mode.
We recommend that you use detergent sparingly for
the sake of the environment. Observe the re-
) position.
commended dilution on the detergent label.
By offering you an individualised range of cleaning
and preserving agents, Bosch guarantees trouble-
free operation of the unit.
L
Only Aquatak 150 PRO/160 PRO X
The product is fitted with one detergent tank. The
detergent adjustment knob 11 is used to increase/
decrease detergent flow.
Only Aquatak 150 PRO X
The product is fitted with two detergent tanks. The
detergent adjustment knob 11 is used to switch the
suction between detergent tanks and increase/de-
crease detergent flow.
Recommended cleaning method
Step 1: Loosening dirt
Spray on detergent sparingly and allow to react for a
short time.
Step 2: Removing dirt
Spray off the loosened dirt with the high-pressure
spray.
Note: When cleaning a vertical surface spray off dirt/
detergent from the bottom and work in an upwards
direction. Rinse from the top and work downwards.
English - 4
Fill the detergent tank 6 with detergent, di-
To spray detergent move vario-jet-fan power