Petsafe Electronic SmartDoor Guide D'emploi page 6

Step 4: Programming your Electronic SmartDoor
Important: It is advised that you program and test your Electronic SmartDoor
installation. It must be in the vertical position for the fl ap to center and operate properly.
1. Programming your Electronic SmartDoor
Press and hold the LEARN button until the green LED begins to fl ash. Release the button. Bring
the SmartKey ™ into range of the Electronic SmartDoor
will illuminate for 2 seconds. The code has been successfully added to memory. Up to fi ve different
SmartKey ™ codes can be added to memory. Only one SmartKey
SmartDoor ™ at a time. Only the SmartKey
SmartKeys ™ have been programmed you may put in the batteries in all the SmartKeys
may be accessed when the Electronic SmartDoor
is activated, if no SmartKey
and extinguish; the Electronic SmartDoor
2. Choosing Automatic, Unlocked, or Locked Mode
Automatic Mode – The SmartDoor
To enter Automatic mode, press and hold the Mode/Reset button: the green LED will illuminate
indicating Unlocked mode, then the yellow LED will illuminate. While the yellow LED is
illuminated, release the Mode/Reset button. The fl ap will enter Automatic mode. The fl ap will move
down (locking). When the unit senses the SmartKey
signal is no longer detected, the fl ap will relock. The SmartKey
Electronic SmartDoor
your pet stays in the range of the door, it will stay unlocked.
Unlocked Mode – The SmartDoor
To enter the Unlocked mode, press and hold the Mode/Reset button; the red LED will illuminate
indicating Locked mode, then the green LED will illuminate. While the green LED is illuminated,
release the Mode/Reset button. The fl ap will unlock.
Locked Mode – The SmartDoor
The Electronic SmartDoor
will enter Locked mode when the 4 D-cell batteries are placed in the Battery Box. To enter Locked
mode when the Electronic SmartDoor
the Mode/Reset button until the red LED is illuminated. While the red LED is illuminated, release
the Mode/Reset button. The fl ap is locked.
Error Mode – When the LED is fl ashing, the Electronic SmartDoor
an error has occurred. If the fl ap is off-of-center, either to the inside or outside, while the fl ap is
lowering, the Electronic SmartDoor
fl ashing. The Electronic SmartDoor
"Troubleshooting" on page 7.
Step 5: Attach the SmartKey
Thread your pet's collar through the SmartKey
attachment loop. Your pet's collar must be ¾" (2 cm) wide or
less. The SmartKey ™
If your pet's collar is too large to thread through the key, a key
ring has been provided. Use for attachment to your pet's collar
ring.
Step 6: Installing your Electronic SmartDoor
See accompanying installation template for installation instructions.
6
™ transmitter signal is detected, the green LED will blink for 60 seconds
™ will only open for the SmartKey
™ for 10 seconds before the door will respond to the SmartKey
is always unlocked.
™
™ is always locked.
ships from the factory in the Locked mode. The Electronic SmartDoor
™
™
™ will stop moving the fl ap down and the yellow LED will begin
™ will remain in Error mode until the error has cleared. See
should hang under the pet's neck.
1-800-732-2677 (US), 1-800-457-3911 (Canada)
to learn the SmartKey
™
™ ; the green LED will stop blinking and
™ being programmed should have a battery in it. When all
™ is in any operating mode. When the Learn mode
™ will return to its previous mode.
™ , the fl ap will unlock. When the SmartKey
is in either the Unlocked or Automatic mode, press and hold
to the Pet's Collar
™
™ 's
™
:
™
™ can be programmed into the
™ .
™ must be out of the range of the
™ is in Error mode, indicating
™
for Use
™ prior to
™ . Learn Mode
™
™ signal again. If
™