stayer SC210BW Instructions D'emploi page 27

Starting with locking
1.Push switch 2.
2.Push locking button 3 whilst keeping switch 2 pushed.
3.Release switch 2.
Stopping the machine when actuated with locking
Push switch 2 briefly.
Use of the lower cutting table
Warning!
1.At those models that are provided with an upper cutting
table, the risk of accidents due to a contact with the cutting
disk appearing at the upper table.
For your own safety, carry out the following preparation
before working with the lower table.
2.It is mandatory to carry out any settings with the cable
unplugged.
Safety setting of the upper cutting table for
cutting operations with the lower table
IMAGES A B O P
Information
This chapter is applicable to models provided with an
upper table: SC250WPRO, SC265W, SC291W SC2500W,
SC2600W and SLL265W.
1.Loosen the screw of the shaft and release lock (38) of
the guard of the upper cutting table 25.
2.Loosen the 3 wing nuts 24 that regulate the height of the
upper table.
3.Raise upper table 25 smoothly pulling upwards until
abutment.
4.Firmly tighten the 3 wing nuts 24.
5.Firmly tighten the screws of the guard of the upper
cutting table 25.
Cutting operation with the lower cutting table
Warning!
1.Respect the limits regarding the size and material of the
workpiece.
2.Use clamps to fasten the workpiece whenever possible.
3.Never lock the motor power switch when working with
the lower cutting table.
The present electrical machine is capable of carrying out
the following kinds of cuts on the lower table:
1.Inclined horizontal cut with a range of 0º to +- 45º.
2.Inclined vertical cut with a range of 0º to 45º.
3.Combinations of the horizontal and vertical ranges (for
example as an abrasive cutoff machine with straight cuts
horizontally at 0º and vertically at 0º).
Setting for inclined horizontal cutting on the
lower table
IMAGES B R
For carrying out inclined cuts horizontally, the machine
head can turn horizontally up to 90º. To facilitate work, the
lower cutting table is provided with 4 pre-set positions at
ENGLISH
27
+- 22º 30' and at +- 45º that may be selected by means
of conical drill holes in the lower cutting table 6 and the
automatic locking bolt 14.
1.Loosen the two buttons 8 for horizontal locking.
2.Raise and keep raised the anchor bolt 14 for pre set
horizontal lockings.
3.Move the assembly cutting head / lower cutting table 6
to the chosen angle by means of the scale
7 that is graduated in degrees and indicator 9.
4.Tighten buttons 8 for horizontal locking.
5.Release anchor bolt 14.
Setting for vertical inclined cutting on the lower
table
IMAGES A G
For carrying out inclined cuts vertically, there are two
abutment inclinations which are calibrated and pre-set at
0º and 45º. Use a goniometer for adjusting to intermediate
angles.
1.Loosen lever 15 for vertical locking.
2.Select the cutting angle.
3.Tighten the lever 15 for vertical locking.
Setting the cutting stopper on the lower table
IMAGES B S T U
1.Loosen screw 39.
2.Insert profile 41 into insertion cavity 44.
3.Push profile 41 into 40 until abutment.
4.Tighten screw 39.
5.Loosen adjusting wing nut 43.
6.Adjust cutting length by moving stopper 42.
7.Tighten adjusting wing nut 43.
Carrying out the cutting operation on the lower
table
IMAGES A B U
1.Prepare workpiece by fastening it in a completely safe
manner.
2.Start the electrical machine by pushing switch 2.
3.Wait for some seconds until the cutting disk reaches its
maximum speed.
4.Slowly lower the operating head by a continuous manner
and without jerks, using hand grip 4.
5.Exert pressure in the blade's direction of advance with
an intensity being suitable for the material to be cut.
6. Once the cutting operation has been completed, raise
operating head again. Stop the machine by pushing switch 2.
Use as circular saw by means of the upper cutting
table
Information:
This chapter is applicable to models provided with an upper
table: SC250WPRO, SC265W, SC291W , SLL265W,
SC2500W and SC2600W.
27