Operation; Important - EINHELL AXXIO Traduction Du Mode D'emploi D'origine

Make sure that the guard is perfectly
secure.
Never use the angle grinder without the
guard.
5.3 Trial run for new grinding wheels
Have the angle grinder run in idle mode for at
least 1 minute with the grinding or cutting wheel
fi tted. Replace vibrating wheels immediately.
5.4 Removing and cleaning the dust guard
(Fig. 4-5)
The angle grinder is equipped with a removable
dust guard (12). This protects the ventilation slots
and keeps the inside of the motor free of dust
and dirt. Ideally the dust guard (12) should be
removed and cleaned each time after the grinder
is used.
To be able to remove the dust guard (12), press it
slightly away from the housing as shown in Fig. 5
to the point where the dust guard can be pressed
downwards and removed (see the direction of the
arrow). The dust guard (12) can be cleaned from
the inside out using low-pressure compressed
air or running water. Before you fi t the dust guard,
make sure that it is fully dry.
To fi t the removable dust guard (12), proceed in
reverse order.

6. Operation

6.1 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Switching on (Fig. 8)
To start the equipment, push the On/Off switch (2)
forwards and press it down. To
switch off the angle grinder, depress the On/Off
switch (2) at the back. The On/
Off switch (2) will jump back into its starting po-
sition.
Wait until the machine has reached its
top speed. You can then position the angle
grinder on the workpiece and machine it.
Note: The equipment switches to "Standby Mode"
after 10 minutes of non-use. To reactivate: Switch
on the equipment twice or press the battery
capacity indicator. "Standby Mode" protects the
battery.
Anl_Axxio_SPK7_USA.indb 16 Anl_Axxio_SPK7_USA.indb 16
EN
6.3 Battery capacity indicator (Fig. 7/Item 10)
Press the battery capacity indicator switch (11).
The battery capacity indicator (10) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive
discharge and is defective. Do not use or charge
a defective battery pack.
6.4 Changing the grinding wheels (Fig. 9-10)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in
the additional handle (3). Pull the face spanner (5)
out of the additional handle (3) when you need it.
Danger! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Warning!
•
Changing the wheel is easy thanks to the
spindle lock.
•
Press the spindle lock and allow the grinding
wheel to engage.
•
Use the face spanner to undo the flange nut.
(see Fig. 10)
•
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.

Important!

Only ever press the spindle lock when the
motor and grinding wheel are at a standstill!
The spindle lock must be kept pressed while
the wheel is being changed!
For grinding or cutting wheels with a thickness of
up to approx. 0.12 in. (3 mm), screw the fl ange nut
on with the fl at side facing the grinding or cutting
wheel.
6.5 Position of the fl anges when using
grinding wheels and cutting wheels (Fig.
11-14)
•
Position of the flange when using an offset or
a straight grinding wheel (Fig. 12)
- Clamping flange (6)
- Flange nut (7)
- 16 -
15.09.2020 14:01:22 15.09.2020 14:01:22