Operation - EINHELL TE-AG 18/150 Li BL Instructions D'origine

5.2 Replacing and adjusting the guard
(Fig. 3)
Replacing:
•
Remove the flange nut (b) and the clamping
flange underneath.
•
Open the clamp lever (a) on the guard (4).
•
Turn the guard (4) through 180° in clockwise
direction so that the guard points upwards.
•
Remove the guard (4).
To mount, proceed in the reverse order.
Adjusting:
•
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
•
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
clamp handle (a) and turn the cover (4) into
the required position.
•
Ensure that the guard (4) correctly covers the
gear wheel casing.
•
Secure the clamp handle (a) again.
•
Ensure that the guard (4) is secure.
Warning!
Make sure that the guard is perfectly secure.
Warning!
Never use the angle grinder without the gu-
ard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi tted in place. Vibrating wheels are to be replaced
immediately.
5.4 Removing and cleaning the dust guard
(Fig. 4-5)
The angle grinder is equipped with a removable
dust guard (10). This protects the ventilation slots
and keeps the inside of the motor free of dust
and dirt. Ideally the dust guard (10) should be
removed and cleaned each time after the grinder
is used.
To be able to remove the dust guard (10), press it
slightly away from the housing as shown in Fig. 5
to the point where the dust guard can be pressed
downwards and removed (see the direction of the
arrow). The dust guard (10) can be cleaned from
the inside out using low-pressure compressed
air or running water. Before you fi t the dust guard,
make sure that it is fully dry.
Anl_TE_AG_18_150_Li_BL_SPK9_1.indb 23 Anl_TE_AG_18_150_Li_BL_SPK9_1.indb 23
GB
To fi t the removable dust guard (10), proceed in
reverse order.

6. Operation

6.1 Charging the Li battery pack (Fig. 6-7)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(7) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 23 -
08.09.2020 09:57:38 08.09.2020 09:57:38