Safety Information; Work Area; Electrical Safety; Personal Safety - IKRA Mogatec HLSI 260 Manuel D'utilisation

Safety information

WARNING. Read and understand all instructions. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious injury. The term "power tool" in
all of the warnings below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool. Save these instructions

Work area

• Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
• Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.

Electrical safety

• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if
your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the risk
of electric shock.
• Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of elec-
tric shock.
• When operating a power tool outdoors, use an
outdoor extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk
of electric shock.

Personal safety

• Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influence
of drugs, alcohol, or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
• Use safety equipment. Always wear eye protection.
Safety equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
• Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turn-
ing the tool on. A wrench or a key that is left attached
to a rotating part of the power tool may result in per-
sonal injury.
GBR | Operating Instruction
• Do not overreach. Keep proper footing and balance at
• Dress properly. Do not wear loose clothing or jewel-
• If devices are provided for the connection of dust

Power tool use and care

• Do not force the power tool. Use the correct power
• Do not use the power tool if the switch does not
• Disconnect the plug from the power source before
• Store idle power tools out of the reach of children
• Maintain power tools. Check for misalignment or
• Use the power tool, accessories and tool bits etc.,

Service

• Have your power tool serviced by a qualified by

Additional safety rules for blower vacs

• Always wear adequate protective clothing when op-
• Do not start the tool when it is upside down or when it
• Switch the motor off and remove the plug when the
GBR-3
all times. This enables better control of the power tool
in unexpected situations.
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
extraction and collection facilities ensure that
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
making any adjustments, changing accessories, or
storing power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool acciden-
tally.
and do not allow persons Unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's opera-
tion. If damaged, have the power tool repaired before
use, Many accidents are caused by poorly maintained
power tools.
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from intended could result in a
hazardous situation.
a qualified repair personnel using only identical
replacement parts. This will ensure that the safety of
the power tool is maintained.
erating the tool to avoid injuries to face, eyes, hands,
feet, head or hearing ,Use safety glasses or a face
shield, high boots or sturdy shoes, long trousers, work
gloves, a hard hat and ear defenders.
is not in the operating position
tool is not being used, left unattended, being cleaned,
being moved from one place to another or when the
extension cord is entangled or damaged.