Technical Specifications - EMAK PW 190 Manuel D'utilisation Et D'entretien

pumped water returns to the suction unit thanks to the pressure control valve. Due to the presence of the Total stop,
(see previous description), this operating mode is only activated in the range of pressures between 0÷20 bar/0÷290 psi,
or should the Total Stop fail to operate.
• Easy Start: this aids starting up the high-pressure cleaner by lowering the pressure for the first moments of its
operation.
2 f
eatures and technIcal
ELECTRICAL CONNECTION
Mains power supply
Absorbed power
Fuse
HYDRAULIC CONNECTION
Maximum inlet water temperature
Minimum inlet water temperature
Minimum inlet water flow
Maximum inlet water pressure
Maximum priming depth
PERFORMANCE
Water flow
Maximum pressure
Recoil of cleaner gun
Sound level
Operator arm vibrations
WEIGHT AND DIMENSION
Lenght x width x height
Weight
Detergent tank
All features and technical specifications are only indications. The Manufacturer reserves the right to modify the appliance as it deems necessary.
2.1 I
dentIfIcatIon of
Please also refer to figures 1 to 4, which are located at the start of these operating and maintenance instructions.
1. Main switch
2. Housing for cleaner gun/lance pipe
3. Detergent tank cap
4. Detergent adjustment control
5. Detergent tank
6. Detergent tank ring
7. Pocket for accessories
8. "Read instructions before..." label
9. "Do not spray persons.." label
10. Pipe reel ring nut (only for PW 210C - IP 2100S)
11 Pipe reel (only for PW 210C - IP 2100S)
12. Pipe reel knob (only for PW 210C - IP 2100S)
13. Identification label
14. Electric wire
15. Connection for water outlet
16. Quick connection for water inlet
17. Pressure adjustment control
2.2 s
afety devIces
This high-pressure cleaner is provided with the following safety devices:
a) Amperometric protector
This blocks the operation of the high-pressure cleaner in case of excessive consumption of electrical current.
In this case, proceed as follows:
- switch the main switch (1) to position '0' and remove the plug from the power outlet;
- press the lever (33) on the cleaner gun to eliminate any remaining pressure;
- wait 10 to 15 minutes until the high-pressure cleaner cools down;
specIfIcatIons
PW 190 - IP 1900
700 l/h / 185 US gph
540 l/h / 142 US gph
14 MPa / 140 bar
components
PW 200 - IP 2000
230 V / 1~50 Hz
2,6 kW
50 °C / 122 °F
5 °C / 41 °F
0,8 MPa / 8 bar / 116 psi
1,5 m / 59 in
15 MPa / 150 bar
2031 psi 2176 psi
88,2 dB (A)
2,30 m/s
48 x 41 x 94 cm / 19 x 16 x 37 in
43 kg / 95 lb
4 l / 1,06 US gal
18. Pressure gauge
19. Cleaner gun
21. Lance pipe
24. Nozzle head
27. Professional, fixed, fan-shaped spray nozzle
29. Nozzle cleaning pin
30. High pressure pipe
31. External detergent suction pipe
32. Safety stop on cleaner gun lever
33. Cleaner gun control lever
34. Quick coupling for high pressure pipe
35. External detergent suction cap
36. Coupling for external detergent suction pipe
37. Detergent suction pipe
38. Coupling for suction of detergent from external tank
39. Inlet water filter
40. Filter for suction pipe of external detergent
PW 210C - IP 2100S
2,9 kW
16 A
800 l/h / 211 US gph
600 l/h / 159 US gph
15 MPa / 150 bar
2176 psi
29 N
2
GB
21