Specifications - EMAK PW 140 Manuel D'utilisation Et D'entretien

2 f
eatures and
ELECTRICAL CONNECTION
Mains power supply
Absorbed power
Fuse
HYDRAULIC CONNECTION
Maximum inlet water temperature
Minimum inlet water temperature
Minimum inlet water flow
Maximum inlet water pressure
Maximum priming depth
PERFORMANCE
Water flow
Maximum pressure
Recoil of cleaner gun
Sound level
Operator arm vibrations
WEIGHT AND DIMENSION
Lenght x width x height
Weight
Detergent bottle capacity
All features and technical specifications are only indications. The Manufacturer reserves
2.1 I
dentIfICatIon
Please also refer to figures 1 to 2, which are located at the start of these operating and maintenance instructions.
1 Water inlet fast connector
2 Main switch
3 Hose reel lever (only PW 150C - IP 1500S)
4 Hose reel (only PW 150C - IP 1500S)
5 High-pressure hose for the hose reel connection
(only PW 150C - IP 1500S)
6 Water outlet connector
7 High-pressure hose for the hose reel
(only PW 150C - IP 1500S)
9 Seat for water gun/lance hose
10 Plate "Read the manual before..."
11 Wire reel
12 Identification plate
13 Plate "Do not spray towards persons, ...."
14 Power supply wire
16 Water gun
17 Lance hose
2.2 s d
afety evICes
This water cleaner is provided with the following safety devices:
a) thermal protector
It's a device that stops the water cleaner operation in case of motor overheating.
In this case, proceed as follows:
• switch the main switch (2) to position "0" and remove the plug from the power outlet;
• press the lever (28) on the cleaner gun to eliminate any remaining pressure;
• wait 10 to 15 minutes until the water cleaner cools down;
• check that the instructions in the
section have been followed, particularly regarding any extension cord used;
• replace the electric plug in the power outlet and repeat the start-up procedure described in the
18
section.
t s
eChnICal peCIfICatIons
the right to modify the appliance as it deems necessary.
C
of omponents
"CheCkS anD ConneCtIon to the maInS eleCtrICIty SuPPly"
PW 140 - IP 1400
2,0 kW
500 l/h / 132 US gph
0,8 MPa / 8 bar / 116 psi
410 l/h / 108 US gph
14 MPa / 140 bars 14,5 MPa / 145 bars
2031 psi
14 N
75 dB (A)
2
1,14 m/s
38 x 32 x 89 cm / 15 x 13 x 35 in
17 kg / 37 lb
18 Nozzle-holding head
19 Nozzle cleaning hole
20 Rotating nozzle lance hose (only
PW 150C - PW 155 - IP 1500S - IP 1550)
21 Foaming lance
22 Cleaner suction adjusting device
23 Detergent bottle
24 High-pressure hose (only PW 140 - PW 155 -
IP 1400 - IP 1550)
25 High-pressure hose fast connector (only
PW 140 - PW 155 - IP 1400 - IP 1550)
26 Water inlet filter
27 Water inlet fast connector
28 Water gun lever
29 Water gun lever safety stop
30 Handle
PW 150C - IP 1500S
230 V / 1~50 Hz
2,3 kW
16 A
50 °C / 122 °F
5 °C / 41 °F
600 l/h / 159 US gph
0 m / 0 in
480 l/h / 127 US gph
2103 psi
16 N
81 dB (A)
2
2,24 m/s
19 kg / 42 lb
0,3 l / 0,08 US gal
PW 155 - IP 1550
15 MPa / 150 bars
2175 psi
15 N
77,2 dB (A)
2
1,77 m/s
18 kg / 40 lb
"oPeratIon"