Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet JWBS-9 Mode D'emploi

No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this
case, protect the machine by
unplugging the mains cord.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit
Do not wear gloves while operating
this machine.
For the safe handling of saw blades
wear work gloves.
Observe the chapter "save operation"
in this manual.
Control the stopping time of the
machine, it may not be longer than
10 seconds.
Insure that the workpiece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Always lower the blade guide to be
close (max 4mm) above the
workpiece.
With the machine table is inclined
use the fence and position it on the
bottom side only.
Always hold and guide the
workpieces safely during machining.
Remove cut and jammed workpieces
only when motor is turned off and the
machine is at a complete standstill.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Pull the mains plug if the
tool is not in use
Pull the mains plug prior
to any maintenance or
change of saw blades.
Before starting the machine make
sure that operating and measuring
tools are removed from the machine.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that
medication can change your
behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Never operate with the guards not in
place – serious risk of injury!
4
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn cord
replaced immediately.
Make all machine
adjustments or
maintenance with the
machine unplugged from
the power source.
Remove defective saw blades
immediately.
Remove a worn table insert.

3.3 Remaining hazards

When using the machine according
to regulations some remaining
hazards may still exist
The moving saw blade in the work
area can cause injury.
Broken saw blades can cause
injuries.
Thrown workpieces can lead to injury
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

Wheel diameter
Cutting width
Cutting height
Sawblade length
Blade width
Blade thickness
Cutting speed
Machine Table(Lx W)
Table tilting range
Dust port diameter
Weight
Mains 230V ~1L/N/PE 50Hz
Motor input power
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Machine lamp halogen

4.2 Noise emission

(Inspection tolerance 4 dB)
Workpiece beech 20mm:
240 mm
max 230 mm
max 80 mm
1510 mm
3 - 10 mm
0,3 – 0,4 mm
670 m/min
300x300 mm
0° to 45°
40 mm
17 kg
350W
1,5 A
10 A
12V, 21W