Remaining Hazards; Technical Data - Jet JMS-10 Mode D'emploi

Always wear the approved working
outfit
- safety goggles
- ear protection
- dust protection
Do not wear gloves while operating
this machine.
For the safe handling of saw blades
wear work gloves.
Control the stopping time of the
machine, it may not be longer than 10
seconds.
Do NOT stop the blade by forcing the
machine or by using sideways
pressure.
Insure that the workpiece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Never use just your hands for
sawing
Take care when slotting
Always hold and guide the
workpieces safely during machining.
Never cut pieces that are too small.
For safety reasons this machine
requires the use of two hands and
should not be operated standing on a
staircase or leather.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Remove cut and jammed workpieces
only when motor is turned off and the
machine is at a complete standstill.
Make sure that the motor ventilation
holes are clean and open.
Stay alert!
Give your work undivided attention.
Use common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Never leave a running machine
unattended.
Before you leave the workplace
switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Do not stand on the machine.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
4
Do not use blades made from High
Speed Steel (HSS).
Remove defective saw blades
immediately.
Select saw blade in relation to
material to be cut.
Use only sawblades recommended
by manufacturer.
Replace table insert when worn.
Do not stare into beam of laser.
Do not point the laser beam at people
or animals.
Do not use the laser beam on highly
reflective materials. Reflected light is
dangerous.
Repair work on the laser beam may
only be carried out by a specialist.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving saw blade in the work
area can cause injury.
Broken saw blades can cause
injuries.
Thrown workpieces can lead to injury
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.
Avoid body contact with earthed or
grounded surfaces (e.g. pipes,
radiators, ranges and refrigerators).
4. Machine specifications

4.1 Technical data

Saw blade size 254x 2,8x 30mm
No load speed
Max cutting height 90°/45°
Max. cutting length 90°/45° 135/90mm
Bevel capacity left
Mitre capacity left/right
Weight
Mains 230V ~1L/N 50-60Hz
Motor input power
Reference current
Extension cord (H05VV-F)
Installation fuse protection
The machine has double insulation
in accordance with EN 61029.
4500 rpm
75/45mm
0°-45°
46°/46°
17 kg
1400W
6,1 A
2x1,0mm²
10A