Mitre Gauge Setup; Tilting Of Machine Table; Maintenance And Inspection; Troubleshooting - Jet JWBS-9 Mode D'emploi

For upper and lower blade guide:
Position the guide assembly forward/
backward so that the teeth keep a
distance of appr. 2mm to the guide
elements (C, G, Fig 7). Secure the
back guide roller (D) so that the
distance to the saw blade (A) is
1mm.
Set the lateral guide elements (C, G)
so that they contact the sawblade
lightly.
The sawblade may not be pushed
out of place.
Fig 7
Turn the wheels by hand and inspect
the adjustments made.
Reattach the sawblade cover and
close the wheel cover.
Bring the upper blade guide to a
distance of max 4mm to the
workpiece.
For your own safety, always set the
blade guide as close to the
workpiece as possible.
Start the machine with care.

7.5 Mitre gauge setup

Setup adjustments shall never be
performed when the machine is
running.
Use a gauge to exactly set up for 90°
Adjust the mitre gauge profile to be
close to the sawblade.
Start the machine with care.

7.6 Tilting of machine table

Setup adjustments shall never be
performed when the machine is
running.
Loosen the indexable knob (A, Fig 4)
to tilt the machine table.
With the machine table inclined use
the fence and position it on the
bottom side only.
For your own safety, always lower
the blade guide as close to the
workpiece as possible.
Start the machine with care.

8. Maintenance and inspection

Make all machine
adjustments or
maintenance with the
machine unplugged from
the power source.
Repair and maintenance work on the
electrical system may only be carried
out by a qualified electrician.
Cleaning:
Clean the machine regularly.
Inspect the proper function of the
dust extraction daily.
Keep the inside of the cabinet clear
of sawdust and wood chips.
All protective and safety devices
must be re-attached immediately
after completed cleaning, repair and
maintenance work.
Defective safety devices must be
replaced immediately.
Wheels:
The rubber tyre of the wheels must
be cleaned regularly.
The upper wheel support must be
lubricated regularly.
Table insert:
Replace a worn table insert
(Jet Article number: JWBS9-073).
The table insert may not project
above table surface.
Machine lamp:
Replace a defective lamp 12V, 21W
(Jet Article Number: JWBS9-130)
Saw blades:
The servicing of saw blades should
only be performed by a trained
person.
Only use sharp and properly set saw
blades.
Replace a defective sawblade
immediately.
Inspect the correct blade tension
regularly. Take away the blade
tension if the machine is not in use
for a longer time period.
Inspect the blade guide adjustment
regularly.
7
9. Trouble shooting
Motor doesn't start
*No electricity-
check mains and fuse.
*Defective switch, motor or cord-
consult an electrician.
Machine vibrates excessively
*Stand on uneven floor-
adjust stand for even support.
*dust on wheel-
clean tires.
*sawblade has cracks-
replace sawblade immediately
Cut is not square
*Table stop setting wrong.
*Blade guide setting is bad
Cutting surfaces is bad
*Wrong sawblade used
*resin collection on sawblade
*sawblade is dull
*Blade guide setting is bad
*Blade tension too low
*workpiece inhomogeneous
*Feed pressure too high-
Do not force the workpiece.
Lamp don't work
*Lamp defect-
Replace the lamp bulb

10. Environmental protection

Protect the environment.
Your appliance contains valuable
materials which can be recovered or
recycled. Please leave it at a
specialized institution.

11. Available accessories

Refer to the JET-Pricelist
for various saw blades.

12. Safe operation

See appendix A (on the last pages of
this operating manual)
A.1: Performing high cuts
A.2.: Performing diagonal cuts
A.3.: Tenon cutting
A.4.: Cutting of wedges
A.5.: Curved cuts
A.6.: Arc cuts
A.7.: Cutting with template
A.8.: Circular cutting
A8.1 Set up without workpiece
A8.2 Placing the workpiece
A8.3 Machining