Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully understand the
operating instructions contained in this Manual.
2. Never leave the POWER TOOL unattended without fi rst unplugging
the power cord.
3. Never operate the POWER TOOL when you are tired, after you
have taken any medications, or have consumed any alcoholic
beverages.
4. Never use the POWER TOOL for applications not specifi ed in the
instruction manual.
5. Never operate the tool while wearing loose clothing, a necktie or
jewelry, or while your hair is uncovered, to protect against getting
caught in the moving machinery.
6. Never reach around the saw blade.
7. Never touch any moving parts, including the blade, while the saw
is in use.
8. Never remove any safety devices or blade guards; use of the tool
without them would be hazardous.
9. Never lock the lower guard; always confi rm that it slides smoothly
before using the tool.
10. Never damage the power cord of the tool.
11. Never attempt to move a plugged-in POWER TOOL while your
fi nger is on the starting switch.
12. Never use the POWER TOOL if the starting switch does not turn
on and off properly.
13. Never use the POWER TOOL if the plastic housing or the handle
is cracked or deformed.
14. Never use the POWER TOOL near fl ammable liquids or gases
because sparking can cause an explosion.
15. Never clean plastic components with solvents because the plastic
may dissolve.
16. Never operate the saw unless all the lower guards are in place.
USE PROPER EXTENSION CORD
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size
to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier
the cord.
Ampere Rating
More
Not More
Than
Than
0 – 6
6 – 10
10 – 12
12 – 16
WARNING:
Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical cord or extension cord.
Inspect all electrical cords regularly. Never use in or near water or in any environment where electric shock
is possible.
17. Never raise the saw blade from the workpiece until it has fi rst come
to a complete stop.
18. Never place your limbs inside of the line next to warning sign
"
conditions.
19. Never use abrasive type blades on this saw.
20. Never expose to rain or use in damp locations.
21. Never cut ferrous metals or masonry.
22. Do not stand in a line with the saw blade In front of the machine.
Always stand aside of the saw blade. This protects your body
against possible kickback. Keep hands, fi ngers and arms away
from the rotating saw blade.
23. Do not cross your arms when operating the tool arm.
WARNING:
FOR YOUR OWN SAFETY READ THIS INSTRUCTION
MANUAL BEFORE OPERATING THE COMPOUND
MITER SAW
1. Always wear eye protection when using the compound miter saw.
2. Always keep hands out of the path of the saw blade.
3. Never operate the saw without the guards in place.
4. Never perform any freehand operation with the compound miter
saw.
5. Never reach around the saw blade.
6. Always turn off tool and wait for saw blade to stop before moving
workpiece or changing settings.
7. Always disconnect power before changing blade or servicing.
8. Saw blade diameter is 12" (305 mm).
9. No load speed is 4300/min.
REPLACEMENT PARTS
When servicing use only identical replacement parts.
Repairs should be conducted only by a metabo HPT authorized
service center.
MINIMUM GAGE FOR CORD SETS
Total Length of Cord in Feet (Meter)
0 – 25
26 – 50
(0 – 7.6)
(7.9 – 15.2)
18
16
18
16
16
16
14
12
" while the tool is being operated. This may cause hazardous
51 – 100
(15.5 – 30.5)
AWG
16
14
14
Not Recommended
English
101 – 150
(30.8 – 45.7)
14
12
12
5
Publicité
Table des Matières
