M-E VISTADOOR ADV-F11 Mode D'emploi page 11

1. The DECT power box must be opened before installation. No tools
are required as the casing is only clicked together. Simple press the
tab on the bottom inwards slightly and then lift the casing lid off
the box as shown in figure A1.
2. Hold the back section with one hand and mark the holes with a
suitable pen.
3. Lay the back section to one side and drill the holes
with a 6 mm drill.
4. Insert the included dowels into the holes and screw the back
section on.
5. Connect the antenna to the power box. It has a screw connection
for this purpose.
NOTE: To optimize the range, you can place the antenna at a different
location using a separately available antenna extension.
COMMISSIONING
When the power box and the outdoor unit have been powered, the red
power LED (4a) on the DECT power box will light up.
Inserting or replacing the battery
Open the battery compartment by pushing it down. Insert the battery
into the socket in the battery slot with a small plug. The plug will only
fit one way into the socket. Do not forcefully push the plug, so as not to
damage the device.
When the battery needs to be changed, simply remove the old battery,
and insert the new one.
Then push the battery compartment lid (23) onto the unit until it snaps
into place.
Connecting the charger / charging the battery
The charger is connected to the power grid via the enclosed power
supply. The LED on the charger lights up red to indicate that the supply
voltage is connected.
To charge the battery in the device, simply place the mobile indoor unit
into the charging unit.
While the battery is charging, the LED above the battery icon on the
handset lights up blue (it does not matter whether the handset is on
or off). When the battery is fully charged, the blue LED goes off. The
handset may remain in the charging unit even when it is fully charged.
Switching handset on and off
The on/off switch for the handset is located at the bottom of the
handset, between the two charging contacts. Turn the switch to „ON"
to turn it on, or „OFF" to turn it off. The LED below the mute icon lights
up blue when the ringtone is activated and the handset is connected to
ADV-F11_I-Manual_210x240_Fin2.indd 11
the power box. If the handset is not connected to the power box, no LED
lights up when the handset is on. If the LED is flashing, the power box
is switched off or out of range.
NOTE: In case of a longer absence (of several days), the handset
should be turned off and removed from the charging unit.
OPERATION
You can connect the power once all components have been installed,
first at the outdoor station and the DECT power box and then at the
DECT indoor station.
The red power LED (4a) should then light up on the DECT power box.
On the DECT indoor station, the status LED (20) should first flash
alternately red/blue and then light permanently after a short time. The
system is then ready for operation and the bell can be activated at the
outdoor station.
Procedure
1. Press the bell button on the outdoor station
2. The blue LED (4b) on the DECT power box flashes and the indoor
station(s) play(s) the set ring melody.
3. Within 60 seconds, the press to talk button (17) can be pressed
and a conversation held with the visitor. All other indoor stations
immediately stop ringing.
4. Any door opener that is connected to the outdoor station can be
activated during the conversation by pressing the door opener
button (19).
5. To end the conversation, press the press to talk button once (17).
Note: after approximately 60 seconds, the DECT indoor station
automatically switches back to standby mode.
Set the ring melody
To change the ringtone, proceed as follows:
1. Open the battery compartment by pushing it down.
2. Press the ringtone key to play the next tune (10).
3. Once the desired tune has been played, put the battery compart-
ment lid back onto the device.
Set the volume of the ring melody
To adjust the ringtone volume, proceed as follows:
1. Open the battery compartment by sliding the battery compartment
lid (23) down.
2. Press the plus button to increase the volume; press the minus
button to decrease the volume.
3. Once the desired volume has been set, put the battery compart-
ment lid back onto the device.
11
ENGLISH | ADV-F11
GB
29.04.15 11:24