Indexa AC50 Mode D'emploi page 29

Add camera
!
Tap „Add Camera" [26] to enroll a new camera, maximum 6 cameras per
smartphone / tablet. Proceed as per chapter 8.
Refresh the connection
!
Tap „Update" [28] to refresh the camera connection.
Activate PIN / Message upon motion detection / Information
!
Tap „information" [29].
!
You can activate the PIN code access after turning on the smartphone /
tablet as follows:
!
Tap „Setup PIN Lock".
!
Enter the chosen PIN two times and a tick by "Enable lock when
starting".
Note: without the valid PIN it is not possible to connect to the camera after
switching on your mobile device. Note your password and keep in a safe
place. If you forget the password the App must be deleted and then
reinstalled and the required cameras set up fresh.
!
In order to send a message through the App, to mobile devices which are
connected with the camera, upon motion detection add a tick against
„Notify Enable" and confirm with "OK". This is required for Android
devices. For iOS the function must be set as follows:
!
Start the setting on the Home side of your iOS device.
!
Select "Notifications".
!
Scroll down to the "OMGuard" App and select this.
!
Set the buttons to " ON" (function activated).
Notes:
#
It can take up to 2 hours before this iOS function is activated by the
provider.
#
There may be a delay in receiving a message dependent on the
messaging service of the provider.
!
Tap „About" to check information about the App. To close this side tap
„OK".
!
To return to the main side tap „Information" [29] or „Close".
10.2 Live image side (see fig. E)
!
To view the live camera image tap the still image on the main side. The live
image is shown in the lower half of the display. To view a larger image turn
the device 90°.
!
To close the live image tap on „Back" [35].
Snapshot / Mute / manual record
!
To make a snapshot of the live image, tap „Snapshot" [32]. The snapshot
will be stored on the smartphone / tablet.
!
To mute or reactivate the sound tap „Audio" [33]. The sound will always
be recorded even if the the sound is muted.
!
To manually start a 2 minute recording tap „record" [34]. The recording is
stored on the microSD card in the camera.
10.3 Operation (see fig. D)
!
Tap on „Operation" [27] on the start side, to access the following
operation functions.
!
Retap on „Operation" to leave the operation side.
Page 29
Set Email upon motion detection / Settings
!
Tap „ Settings" [22] to select the camera system information (see fig. G).
!
Tick on „Enable Email Alert" if an Email should be sent to the set Email
address in event of motion detection (insert tick or push button to the right)
!
Tap „Advanced Settings" to enter the Settings side (see Chapter 9).
!
To save the settings tap „Save" [48] and confirm with „Yes" or „OK".
Delete camera
!
To delete the camera from the App tap „Delete Camera" [23] and confirm
with „Yes". It is not necessary to delete the camera in regular use.
View and delete recordings (see fig. F)
!
Tap on the event list [24] to view the recordings on the microSD card
within the last hour
!
To view further recordings tap [40] or „Search", tap on the chosen time
frame. Confirm with „Yes" for Android devices.
!
Tap on the desired file to view the recording. If, due to poor connection,
there is no image then wait approx. 1 minute and try to replay the recoding
again.
!
To delete an individual recording using an Android device select: "Delete"
[39] and tick against the recording. To delete all recordings tap the symbol
with 4 squares. After selecting tap the bin symbol and confirm with "Yes".
For iOS select "Delete All"and cofirm with "Yes", or "Delete One" and then
tap the round red symbol in front of the recording and confirm with
"Delete".
!
To close the list tap on the back symbol.
11. Installation
!
Before fixing the camera permanently, test the quality of the connection
and optimise the camera view.
The camera can be wall or ceiling mou
!
Firstly disconnect all cables.
!
For wall or ceiling installation mount the b
using the screws [19] and if necessary the wall plugs [18] provided.
!
Screw the bracket into the appropiate threaded hole [13] in the camera
housing.
!
Adjust the angle of the camera to give the required view and then tighten
the triangular nut [7] and the wing screw [8].
!
Screw the antenna [6] into the antenna connection [12] so that the
antenna is in an upright position.
!
If the connection to WiFi router is desired via network cable then connect
the camera to via the local network with the network plug [14].
!
Connect the mains adapter with a suitable mains outlet. The POWER LED
[3] lights red.
12. Motion detection recording and alert
The camera runs a motion detection software which detects image changes and
automatically activates a recording and an alert message. This function
requires that a formatted microSD card is fitted. If no microSD card is fitted only
the App connection to live images is possible.
#
If the microSD card is fitted, the software is active. When an image change
is detected, a two minute recording with video and sound is automatically
.
nted (see fig. A: I and II).
racket [9] at a suitable location
GB - 29