Fuel To Be Used; Identification Plate; Supplied Accessories; Installation - ZANTIA CRONOS Manuel D'utilisation Et D'entretien

1.9

FUEL TO BE USED

The product works exclusively with pellets, cylindrical shaped
fuel obtained by mixing various types of wood pursuant to
standard DIN 51731. Therefore pellets with features differ-
ent than those foreseen by the standard downgrade the ef-
ficiency of the appliance, causing bad combustion and the
formation of encrustations.
1.10

IDENTIFICATION PLATE

fig. 1 identification plate
The identification plate is applied on the back of the product.
1.11

SUPPLIED ACCESSORIES

The product is supplied together with:
• Power cables;
• Adjustable feet;
• Instruction booklet.
2

INSTALLATION

The indications contained in this chapter refer expressly to the
Italian installation standard UNI 10683. In any case, always re-
EN
spect the standards in force in the country of installation.
2.1

INITIAL RECOMMENDATIONS

The installation position must be chosen depending on the
room, exhaust and flue. Check with local officials whether there
are more restrictive prescriptions regarding fuel air intake and
flue gas exhaust system including flue and chimney. The manu-
facturing company will not be held liable in case of installation
nonconforming to laws in force, of an incorrect air exchange in
the rooms, of an electric connection nonconforming to stand-
ards and of inappropriate use of the appliance. Installation must
be carried out by a qualified, skilled technician who must issue
the purchaser with a declaration of conformity of the plant and
take on full responsibility for the final installation and conse-
quent correct operation of the product. He must especially
make sure that:
• There is an appropriate combustion air intake and a flue
gas exhaust compliant to the type of product installed;
• Other stoves or installed devices do not put the room
34
where the product is installed in negative pressure (only
airtight appliances are allowed a maximum of 15 Pa of
negative environmental pressure);
• There is no flue gas backflow into the room with the prod-
uct lit;
• Flue gas exhaust is implemented in full safety (dimension-
ing, flue gas sealing, distance from flammable materials).
It is especially recommended to check the data on the
flue identification plate for the safety distances which
must be respected in the presence of combustible ma-
terials and the type of insulation material to be used.
These prescriptions must always be strictly respected
to avoid serious damage to personal health and to the integrity
of the home. Installation must guarantee easy access in order to
clean the device, the flue gas pipes and the flue. Installation in
single room apartments, bedrooms and baths is only allowed for
airtight or closed appliances provided with appropriate combus-
tion air ducting directly outside. Always maintain an appropriate
distance and protection to keep the product from coming into
contact with water. Should several appliances be installed, the
outside air intake must be dimensioned accordingly.
2.2

HANDLING AND TRANSPORT

Make sure that the lifting and transport devices used bear the
weight of the boiler indicated in chap.8 "Technical data". Lift
the boiler using a forklift truck, whose forks must be inserted
inside the specific seats of the wooden crate.

Place the product on the floor with caution, avoiding
any impact in order to position it in the room.
2.3

PACKAGE OPENING PROCEDURE

Remove all the parts making up the package (polystyrene,
wood, plastic).
similar use or disposed of as urban waste in compliance with
standards in force.
After having removed the packaging, make
sure that the product is intact.
Handle the appliance with suitable means
paying attention to the relevant safety stand-
ards in force. Do not tip the package over.
To open the package, proceed as follows:
• Remove the fasteners (fig.3) to the pallet;
• Unscrew the fixing screws (fig.3 ref. A) of the boiler base
located underneath the pallet;
• Handle the product by hand, placing it near the installa-
tion site
translated from the original text
fig. 2 lifting package
All the packaging materials can be reused for
Installation
Mod. CRONOS rev 01