Applications; Music Control - IMG STAGELINE COLOR-150 Mode D'emploi

3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning - This appliance must be earthed.
If the unit is to be put out of operation de-
finitively, take it to a local recycling plant for
a disposal which is not harmful to the envi-
ronment.

3 Applications

The unit COLOR-150 is especially suited for applica-
tions on stage and in the discothèque. It projects a
light cone whose colour can be changed by remote
control. It is equipped with a blackout function with
automatic switching off of the lamp. The control of the
unit can be made via the integrated microphone, via
the remote control LC-2 (separately available as an
accessory), or via a DMX light control unit.
4 Inserting a Halogen Lamp
The unit is supplied without lamp. A reflector halogen
lamp with the following specifications is required:
15 V/150 W, type MR 16 with base GZ 6,35 (e. g. HLO-
15/150MR or HLP-15/150L from the product range of
"img Stage Line").
Never use a lamp with a higher wattage than 150 W!
Caution!
Always disconnect the mains plug before inserting or
removing the halogen lamp! As halogen lamps heat
up very much during operation, let the lamp first cool
down after operation of the unit (minimum cooling
down time 15 minutes) before replacing it.
1) Unscrew the screw for the cover of the lamp com-
partment (6). Pull out the cover backwards. The
lamp support is in the compartment (fig. 4).
2) Insert the halogen lamp into the support and push
on the lamp connection (fig. 5). Pay attention that
the lamp is centered in the support.
3) Close the cover again and fasten it with the screw.
Never operate the unit without cover. Looking
directly into the lit halogen lamp may cause eye
damage due to the high brightness and the UV
radiation.
5 Mounting
The unit can be placed on a firm, even, heat-resistant
surface. However, it can also be suspended from a
crossbar. For this purpose fasten the supplied mount-
ing bracket (1) with the two setscrews (2) to the sides
of the unit. For adjusting the unit, release the two set-
screws (2) at the mounting bracket. Adjust the desired
inclination of the unit and tighten the screws again.
Important!
1. To prevent heat accumulation within the unit, the
mounting location must be selected in such a way
that a sufficient air circulation will be ensured
during operation. The unit must have a minimum
distance of 25 cm to adjoining surfaces and the air
vents at the housing must not be covered in any
case.
2. Pay in any case attention to a sufficient distance to
easily flammable material or material sensitive to
heat.
3. If the unit is installed as a suspended load above
persons, it must additionally be secured (e. g. by a
safety rope). Fix the safety rope in such a way that
the maximum falling distance of the unit is 20 cm.
6 Operation
Connect the plug of the mains cable (10) to a mains
socket (230 V~/50 Hz). Thus, the unit is switched on.
The unit first switches off the light for approx. 8 s. Then
the unit is ready for operation. To switch off the unit,
disconnect the mains plug.
For a more convenient operation it is recommend-
ed to connect the unit to a mains socket which can be
switched on and off via a light switch.

6.1 Music control

To control the COLOR-150 via the integrated micro-
phone (5), set the DIP switch No. 10 (4) to position
ON, as shown in fig. 6. The unit now independently
changes the colours at certain intervals. If the music is
played with a distinct rhythm in the bass range at suffi-
cient volume, the colour change is synchronized with
the rhythm of the music.
1 2 3 4 5 6 7 8 9 10
ON
Music control via the integrated microphone
GB
9