Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
6.1.1 Interconnecting several COLOR-150
GB
Several units can be interconnected in order to control
all further (slave) units to the same rhythm via the
microphone of the master unit. Up to three slave units
can be controlled via the master unit.
1) Adjust the DIP switches (4) at the master unit as
shown in fig. 6.
2) Adjust the DIP switches at the slave units (slaves 1
to 3) according to fig. 7
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
Control of the slaves by the master
3) Connect the output (7) of the master unit via a
3-pole XLR cable (e. g. series MEC-... or MECN-...
from the product range of "img Stage Line") to the
input (8) of the first slave unit.
4) Connect the output (7) of the first slave unit to the
input (8) of the second slave unit, etc.
6.2 Remote control LC-2
Via the remote control LC-2 available as an accessory
different functions may be controlled:
1) Connect the remote control to the jack (9).
2) Set the DIP switch No. 10 (4) to position ON, as
shown in fig. 6.
3) Via the output DMX (7) it is possible to connect fur-
ther COLOR-150 units (see chapter 6.1.1) to con-
trol them synchronously with the remote control.
4) The following functions may be controlled via the
remote control:
Button FAST/SLOW (14):
After switching on, the fast mode is activated. The
LED next to the button does not light up. The
colours are changed by music control or automati-
cally at certain intervals if there is no music. If the
unit is switched to the slow mode with the button,
the LED lights up and the colours are changed with
the button STROBE/NEXT. To return to the fast
mode, press the button FAST/SLOW again.
Button STROBE/NEXT (13):
a) In the fast mode [The LED next to the button
FAST/SLOW (14) does not light up.]
As long as the button is pressed, the music-con-
trolled strobe effect is activated.
b) In the slow mode [The LED next to the button
FAST/SLOW lights up.]
With each pressing of the button, the unit chang-
es to the next colour.
10
7
8
9
10
Slave 1
ON
7
8
9
10
Slave 2
ON
7
8
9
10
Slave 3
ON
Button STAND BY (12) for the function Blackout:
The light is extinguished. After a short time the
halogen lamp is switched off. As an indication, the
LED next to the button lights up. To switch back,
press the button again.
6.3 Operation via a light control unit
For operation via a light control unit the COLOR-150 is
equipped with a 1-channel DMX receiver.
The exact assignment of the individual colours and
functions is indicated in the specifications chapter 8.1.
1) Connect the input (8) via a 3-pole XLR cable to the
DMX output of the light control unit.
For connection, special cables for high data flow
should be used. The use of standard microphone
cables can only be recommended for a total cable
length of up to 100 m. The best transmission results
are obtained with a screened microphone cable of
2 x 0.25 mm
2
or a special data transmission cable.
For cable lengths exceeding 150 m it is recom-
mended to insert a DMX level matching amplifier
(e. g. SR-103DMX from "img Stage Line").
2) Connect the output (7) to the DMX input of the next
light effect unit whose output is again connected to
the input of the following unit etc. until all light effect
units are connected.
The DMX output jack has a latching. To pull out the
plug, press the PUSH lever.
3) Terminate the DMX output of the last light effect unit
in the row with a 120 Ω resistor (0.25 W): Solder the
resistor to the pins 2 and 3 of an XLR plug and
connect the plug to the DMX output.
4) With the DIP switches (4) adjust the binary number
of the DMX address which is provided at the DMX-
512 control unit for the control of the COLOR-150.
The address results from the addition of the
switch values of the DIP switches (1, 2, 4 ... 128,
256) which are set to ON, shown in the following
figure, e. g.:
1
2
3
4
5
6
7
8
9
10
ON
1
2
3
4
5
6
7
8
9
10
ON
1
2
3
4
5
6
7
8
9
10
ON
Adjusting the DMX address
address 1
address 13
1 + 4 + 8 = 13
address 144
16 + 128 = 144
Publicité
Table des Matières
