Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Using as a handheld
CAUTION!
Never use the squeegee on cold glass and win-
dows as it may cause damage.
Attach desired accessory as described, > "Attaching
1
accessories" on page 18.
2
socket.
Turn steam control dial to 'ON' (Fig.
3
➔ The power-on indicator turns red. The steamer
starts heating up and will be ready after approx. 30 s.
Twist steam control dial to desired setting (Fig.
4
Push handheld steam trigger in short bursts to
5
produce steam (Fig.
).
18
6
'OFF' . ➔ The steamer will cool down, the power-on
indicator will switch off.
7
mains socket.
When steamer is cooled down dis-
8
connect accessory.
Attaching accessories
Attaching brushes
Push brush and jet nozzle together. Push hard un-
1
til you hear a click. (Fig.
).
10
the steamer until it clicks into place (Fig.
Attaching utility head
Stretch utility pad over utility head (Fig.
1
Push utility head into steamer. It will not lock into
place. Pull test to check it is secure.
Attaching squeegee
Stretch utility pad over utility head (Fig.
1
Align the tab on the squeegee with utility head
2
and pad, push together to lock into position (Fig.
Push utility head into steamer. It will not lock into
3
place. Pull test to check it is secure.
Storing the steamer
Stand steamer upright by pushing the main body
1
forward to lock into position (Fig.
from the mains socket and wind cord around the
quick cord release hooks (Fig.
Maintaining the appliance
Emptying the water tank
!
WARNING!
Hot surface! Only empty the water tank when the
steamer is cooled down.
Switch off the steamer and pull the plug from the
1
mains socket. Let steamer cool down.
held release button and disconnect handle from the
main body (Fig.
).
5
Insert the plug into a mains
16
).
).
16
Turn steam control dial to
Unplug the plug from the
Push jet nozzle into
2
).
11
12
).
2
).
12
13
).
4
).
Pull plug
2
).
22
Push hand-
2
EN
Push accessory release button and disconnect
3
main body from floorhead (Fig.
body on flat surface.
5
clockwise and lift to remove (Fig.
excess water over an empty sink (Fig.
water tank cap and twist clockwise to tighten.
Cleaning the microfibre and utility pad
CAUTION!
Don't use bleach or fabric softener when washing
the microfibre and utility pad.
Wash microfibre pad in the washing machine
1
(max. 40 °C) or handwash the utility pad (Fig.
Leave the cleaned pad to dry completely for at
2
least 24 h.
Clearing blockages
CAUTION!
Don't use sharp objects to remove blockages.
Disconnect floorhead from the main body
1
(Fig.
).
Disconnect handle from the main body
6
2
(Fig.
5
).
Use a small thin object (e.g. a paperclip)
3
to insert into the nozzle and clear any blockage
(Fig.
).
Remove microfibre pad from the floor-
20
4
head and insert a small, thin object (e.g. a paper-
clip) into the steam holes to remove any blockage
(Fig.
).
21
Accessories
• 1 carpetglider – 03250006 (Fig.
• 1 jet nozzle – 0325007 (Fig.
• 1 microfibre pad – 0325001 (Fig.
• 1 crevice brush – 0325008 (Fig.
• 1 plastic brush – 0325009 (Fig.
Troubleshooting
!
WARNING!
Switch off the appliance before you start trouble-
shooting. Never use a faulty appliance.
Before you contact our Dirt Devil customer service
department or send the appliance to the Dirt Devil
customer service department, you will find a lot of
additional information in the service area of our web-
site which will help you solve problems.
www.dirtdevil.de/service
19
6
).
Place main
4
Twist water tank cap anti
).
Empty any
7
6
9
).
Replace
7
).
19
/A)
23
/B)
23
23
/C)
23
/D)
/E)
23
Publicité
Table des Matières
