Before First Use - SOLIS ULTRA X-PRESS 8326 Mode D'emploi

NOTE S FO R T H E 5 AU T OM AT IC P RO G RA MS
n
• In all 5 automatic programs, only the blending time can be increased with the
button . The blending speed can not be influenced. This is the reason why
the speed bar does not light up while an automatic program is activated.
• You can pause every automatic program by touching the corresponding pro-
gram button, e.g. to add ingredients through the lid opening. The time in the
display is stopped and „PAUS" is displayed. Once you touch the program button
again, the program is resumed and the time continues to count down.
• Should you wish to completely cancel the automatic program while the program
is running, you can touch the ON/OFF button at any time.
• We strongly advise against pressing the button
finished, with the time standing at 0:00. This should always be done before a
program finishes. If you want to restart the appliance even though the display
already states 0:00, you should pull the power plug, lift the blender jug off of
the motor base, place the blender jug back on the motor base after a few sec-
onds, reconnect the power plug after and restart the appliance.
s BEFORE FIRST USE
• Before using your Solis Ultra X-Press for the first time, please remove all packag-
ing and advertising materials as well as stickers. Do not plug the power plug into
the power outlet yet. Clean the lid including the cap seal and the blender jug as
well as the blade base in warm dishwater with a soft dish rag. Rinse everything
carefully with clear water and dry everything. The blender jug and the lid can
be cleaned in the dishwasher. Please make sure that the lid has been removed
before placing the jug in the dishwasher. The motor base must not be placed in
the dishwasher, it should be cleaned with a soft, only slightly moist towel and
then be dried.
The blending blades are extremely sharp. Avoid any contact with your
fingers resp. your hand!
Note: When using your blender for the first time, the factory-fresh motor might
cause a light smell. This is normal and wears off after a short time.
102
again after a program has
s STARTING UP
• After getting comfortable with the functions of your Solis high speed blender,
you can now start using the appliance.
1. Place the motor base on a dry, moisture resistant, even and stable work surface,
at least 10 cm away from a table edge.
2. Fill the blender jug with the food, paying attention to the MAX marking on the
jug. A maximum of 2 litres of food can be blended. Please keep in mind that
some foods might increase in volume through blending.
3. Place the lid on the blender jug and push it all the way down, so that the blender
jug is fully sealed all around. Place the seal cap on the lid, guiding the noses of
the cap into the notch by the symbol „open lock" on the lid, then screw the
cap clockwisely all the way in.
4. Place the blender jug on the motor base, it should smoothly glide over the four
rubber knobs and sit on the motor base evenly.
5. Plug the power plug into a suitable power outlet. Shortly afterwards, the symbol
at the ON/OFF button lights up.
6. Touch the ON/OFF button . It starts flashing and all function buttons light
up.
Attention: Place a hand on the lid when the blending process starts to prevent
it from loosening, especially if the jug is well filled or filled with hard foods. You
can let go of the lid once the foods are chopped.
7. Choose a program (one of the 5 automatic programs or a manual speed setting)
by touching the corresponding button. If you have chosen the manual speed
setting, start with the button and gradually increase the speed until you
reach the desired intensity.
8. The selected program starts up, operation time is counted down in the display.
9. If you wish to increase blending time, press the
if desired. The time is added in the display.
10. When the set program is finished, the appliance automatically switches off. The
motor ventilator built into the appliance will keep running for some seconds
after the appliance is switched off. It is therefore possible that a ventilation
sound can be heard even after switching off. The ventilator switches off auto-
matically after a short period of time.
11. Only then pull the plug from the socket with dry hands and remove the blender
jug. To remove, pull the blender jug upwards without turning it. Only remove
the blender jug after the power plug has been pulled and the blades has come
to a complete standstill.
button, even multiple times
103