Mounting And Operation; Working Advice - Bosch AQT 35-12 Notice Originale

OBJ_BUCH-1953-005.book Page 12 Monday, December 16, 2013 1:37 PM
12 | English
Equipment category: 27
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS23,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
06.12.2013

Mounting and Operation

Action
Delivery Scope
Fold down handle operation
Connecting high pressure gun to lance
Connecting high pressure water supply hose/
nozzle
Attaching Nozzles
Water connection
Switching On and Off
Adjust water jet
Connect detergent bottle
Clean the water filter
Clean nozzle
Gun storage
Gun/lance/nozzle is stored in action
Hose into the hose holder
Storage
Selecting Accessories
Starting
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
- 1.5 mm – max length 20 m
2
- 2.5 mm – max length 50 m
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
F 016 L70 995 | (16.12.13)
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
Figure splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
1
Products sold in GB only: Your product is fitted with an
2
BS 1363/A approved electric plug with internal fuse (ASTA
3
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
4
cut off and an appropriate plug fitted in its place by an author-
5 ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
6
The severed plug must be disposed of to avoid a possible
7
shock hazard and should never be inserted into a mains sock-
8
et elsewhere.
9
To prevent damage to the appliance, do not allow it to operate
10
dry.
11
Operation
12
13
Starting
14
Attach water supply hose (not supplied) to the mains water
15
supply and machine.
16
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and water
supply hose. Release trigger. Press the safety lock (front but-
ton on the gun handle).
Turn button on main switch. Point the power gun downwards.
Press the trigger safety lock to release the trigger. Fully press
the trigger.
Autostop function
The machine is designed to switch off the motor when the trig-
ger is released on the gun.

Working Advice

General
Ensure that the pressure washer is on level ground.
Bosch Power Tools