Publicité
Les langues disponibles
Les langues disponibles
push bearing that is big enough to contain the axel itself.
• Insert the chamber on the axel making sure that the support
brackets are also be installed correctly (Pic. 3)
Check that the wheel turns freely.
Warning
Use original spare parts exclusively provided by Fac Mi-
chelin S.r.l.. Any modification or alteration (also graphic)
of the product with non-original spare parts or spare
parts not delivered directly by Fac Michelin S.r.l., invol-
ves the expiration of the guarantee.
Rear hub
The rear hub requires cleaning and lubrication of the ratchets in
the freewheel body.
For any maintenance:
• Insert allen wrentch 12mm (M) on left side of the hub (Pic. 4).
• Using adjustable wrentch, unscrew left stop (O)
Extract the axel of rear hub with the freehub body (c). if necessary
at this point you can:
• Change the bearings.
• Grease the cogs with low density grease (Pic. 5).
• Extract from the axel the freehub body with the relative spacer (Z)
continue the cleaning process of hub.
Warning: the bearings of the freehub body and no re-
placeable.
• Re-fit the axel (C) inside hub body with the spacer (Z) (Pic. 6).
Take care to position of the pawls (Pic. 4)
• Insert allen wrentch 12mm(M) on left side of the hub (Pic. 6).
• Stopping left stop (O) with adjustable wrentch (N) locking at 15
Nm (Pic. 6)
• If necessary adjust the hub by working on the ring (H) (Pic. 6):
• Unlock the grub screw (I) with a allen wrentch 2mm (L) (Pic. 6).
• Turn the ring in clock sense to drop the sliding, and in anti-clock
sense to rise the sliding. Lock the grub screw (I).
Check the sliding of the wheel.
Please check that the hub is correctly tightened and
closed, failure to do so could lead to a serious or fatal
accident.
Warning
Use original spare parts exclusively provided by Fac Mi-
chelin S.r.l.. Any modification or alteration (also graphic)
of the product with non-original spare parts or spare
parts not delivered directly by Fac Michelin S.r.l., invol-
ves the expiration of the guarantee.
SECTION III -
Spokes
The spokes used for the assembly of the wheels have the following
sizes and characteristics:
Rear wheel
Right side (opposite side to the disc)
Left side (disc side)
Front wheel
Right side (opposite side to the disc
Left side (disc side)
CHANGE A SPOKE
Warning
If you have any doubt whatsoever your service-repair abi-
lity, please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, al-
ways wear gloves and protection glasses.
Use only spokes of the same length and characteristics
of those to be replaced.
Use original spare parts exclusively provided by Fac Mi-
chelin S.r.l..
To replace a spoke on the SWR T DX is extremely easy in both
cases, front as well as rear wheels.
• Unscrew the spoke from the nipples with the corresponding
spanner.
• Once it has been unscrewed, slide off the spoke from its own
seat.
• Insert the new spoke
• Screw nipple with washer
Draw the spoke to be used for the replacement in the thread-locker
you chose to improve sealing.
To ensure the correct spoke tension please follow the
indications below:
• Correct spoke tension for front wheel (disc side) 1000N
• Correct spoke tension for rear wheel, free wheel side 1300N
To evaluate the correct wheel tension, please use a professional
spoke tension gauge, we do not recommend that spoke tension
is estimated manually; please refer to a professional cycle mecha-
nic if you do not own a professional spoke tension gauge. The
correct spoke tension is essential to ensure a ridged and durable
wheelset.
ATTENTION in correct spoke tension, too high or too low,
could lead to wheel failure and resulting serious or fatal
accident.
SECTION IV -
SWR T DX wheels are developed to set up clincher tyre.
Please ensure that the wheels are not subject to direct shock from
poor road surfaces [i.e. pot holes] ATTENTION direct shock to
the wheels from poor road surfaces could lead to whe-
el failure and resulting serious or fatal accident. In the
event your wheels are subject to any such shocks from poor road
surfaces, yet do show the signs of any damage we advise you to
immediately have the wheels checked by a qualified mechanic or
other qualified person.
276 mm
266,5 mm
269 mm
276,5 mm
5
Complete wheels
Publicité
