Dometic ACE AIR PRO 400 Notice D'utilisation page 11

This manual provides information that is necessary for proper installation
and/or operation of the awning. Poor installation and/or improper oper-
ating or maintenance will result in unsatisfactory performance and a possi-
ble failure.
The manufacturer accepts no liability for any injury or damage to the prod-
uct resulting from:
• Incorrect assembly or connection, including excess voltage
• Incorrect maintenance or use of spare parts other than original spare
parts provided by the manufacturer
• Alterations to the product without express permission from the manu-
facturer
• Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product
specifications.
This product is only suitable for the intended purpose and application in
accordance with these instructions.
This manual provides information that is necessary for proper installation
and/or operation of the product. Poor installation and/or improper oper-
ating or maintenance will result in unsatisfactory performance and a possi-
ble failure.
The manufacturer accepts no liability for any injury or damage to the prod-
uct resulting from:
• Incorrect assembly or connection, including excess voltage
• Incorrect maintenance or use of spare parts other than original spare
parts provided by the manufacturer
• Alterations to the product without express permission from the manu-
facturer
• Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product
specifications.
Using the awning
!
CAUTION! Risk of injury and material damage
Never open the zipper on the protective sleeve while an air
pole is inflated. This will result in the air pole bursting.
Before first use
Familiarize yourself with the product by carrying out a test set up before
the product is used for the first time. Check if the scope of delivery is
complete.
Choosing a site
Choose a flat site that is protected from wind:
1. If necessary, use a windbreak.
2. Choose a shaded site to avoid UV degradation of the fabric.
3. Avoid pitching under trees as falling branches, resin, etc. can damage
the product.
4. Clear the site of sharp stones and debris to avoid damaging the
groundsheet.
5. Set up the product with the doors facing away from the wind.
Setting up the awning
!
CAUTION! Risk of injury and material damage
• Do not use any type of compressor designed to inflate
car tires.
• Only inflate the air poles into the green zone of the
pressure gauge of the supplied hand pump
(9 psi/0.62 bar).
EN
A
NOTICE! Material damage
• Do not open or close the zippers by force.
• If a wind-out awning is used to attach the awning,
support the wind-out awning while working to avoid
putting too much stress on it. After attaching the
awning, rewind the wind-out awning fully back into its
housing.
I
NOTE
• The awning comes with heavy duty pegs. These will be
suitable for many sites but for some types of ground
special pegs will be needed. Ask your dealer.
• Drive the pegs at a 45° angle away from the awning into
the ground.
• Peg the guy lines in line with the seam it starts from.
Keep the following tips in mind while setting up the awning:
• The figures provide a general overview of the set-up. The actual set-up
will vary slightly based on the model of awning.
• Get help. The set-up is easier with more people.
• After standing the awning upright, check the corner pegs and re-peg
if necessary. The groundsheet on the inside should be taut and in a
rectangular shape.
• Peg the guy lines so that the awning is under tension without distorting
the shape.
• If available, attach the storm straps.
• Check the guy lines from time to time to ensure adequate tension, if
necessary use the runners to adjust.
Set up the awning as follows:
1. To protect the awning from dirt and damage, lay down a ground-
sheet or footprint before unpacking.
2. Unpack the awning.
3. Separate and identify the different components.
4. Proceed as shown to set up the awning (fig. 3, page 5 to fig. l,
page 8).
Only Ace AIR PRO500:
5. Inflate the additional air pole.
6. Fix the inflated air pole into place in the middle back roof panel using
the velcro fasteners.
Dismantling the awning
A
NOTICE! Material damage
Do not use force when dismantling the awning. Otherwise
you might damage any material.
1. Remove any dirt on the outside.
2. Close all window blinds or remove curtains.
3. Close all doors and openings.
4. If installed, push the canopy pole out of the sleeve, do not pull.
5. Remove all lines and straps.
6. Remove all pegs between the corner pegs.
7. Open the valves on each pole.
8. Wait until most of the air has been expelled.
9. Remove the four corner pegs.
10. Fold/roll the awning towards the valves to expel more air.
11. When deflated, roll the awning to fit into the carry bag.
12. Ensure that all parts are clean before packing the into the carry bag.
13. If the awning is wet or damp, dry fully as soon as possible.
4445103255 11