Software Instructions; Maintenance And Inactivity - GAIA fresh milk Manuel D'emploi Et D'entretien

5.0 SOFTWARE INSTRUCTIONS

STANDARD MODE
PUSHBUTTON PANEL
The pushbuttons provided are meant for:
P1
SHORT COFFEE
P2 LONG COFFEE
P3 WHITE COFFEE-MILK POWDER
P4 WHITE COFFEE-FRESH MILK
P5 CAPPUCCINO-MILK POWDER
P6 CAPPUCCINO-FRESH MILK
P7 CHOCOLATE
P8 MILK - FRESH MILK
MAINTENANCE
KEY
PROGRAMMING
KEY
Access to Programming
Access the programming menu by pressing on the pushbutton located to
the rear of the keypad
In the programming mode the keys have the following meaning:
Key 1: Increase value
Key 2: Escape
Key 3: Decrease value
Key 5: Move cursor
key 7: Enter / scroll options
Access the maintenance
Access the maintenance menu by pressing on the pushbutton located to the
rear of the keypad.
Holding the maintenance key pressed in for 5 seconds will reset the coffee
grounds error message.
The pushbuttons provided are meant for:
Key 1: Alarms scroll-down
2nd level function
Key 2: Alarm reset
Alarm reset
Key 3: Complete test run
Key 4: Only water test
Key 5: Mixer test
Key 6: Group movements
Key 7: View total selections
MDB tube filling
Key 8: Cleaning
MDB tube emptying
MENU DOSES
You can set or change the parameters of the Fresh Milk solenoid valve, which
regulates the amount of steam for the various items on the list.
Milk emulsion can be improved via the "T on / T off" function, which controls
the opening and closing of the steam solenoid valve during dispensing.
MENU TIME AND THRESHOLDS
There are 3 different types of washing for the fresh milk circuit:
1. rapid automatic
2. intensive
3. daily manual (see Maintenance)
1.RAPID AUTOMATIC WASHING
Delivery is not possible during this stage.
This function activates when the machine has been inactive for a few seconds
after the last dispensing of fresh milk. The default value is 0.0 seconds, which
means the function is not active.
The management algorithm is fixed, as follows:
Active on cascade
Fresh Milk SV for 1.5 sec.
SV5 for 2 seconds
Fresh Milk SV for 1.5 sec.
2. INTENSIVE WASHING
During this stage all the buttons are deactivated, except for the one asso-
ciated with washing.
This function activates whenever the machine is switched on and after it has
been inactive for a few hours. The default value is 3 hours. If it is set to 0.0
hours, this function is deactivated.
When the set time has elapsed, the fresh milk solenoid valve is disabled and
the drinks associated with it can no longer be delivered.
The management algorithm is fixed and as follows:
Active on cascade
Fresh Milk SV for 5 sec.
SV5 for 3 sec.
Fresh Milk SV for 5 sec.
Each time the vending machine is switched on,
you will be prompted to press P4 for 3 seconds
to perform the washing cycle and enable me-
tering with fresh milk.
WASHING NOT CONTROLLED BY USER:
Repeat washing of milk circuit
An automatic washing cycle is provided for
1.5s (fixed) at the end of each fresh milk di-
spensing cycle.

6.0 MAINTENANCE AND INACTIVITY

6.1 Cleaning and Loading
So as to guarantee the correct functioning of the distributor during
time it is necessary to effect some operations periodically, some of
which are indispensable for the observance of the health standard
norms. These operations must be done with the distributor open and
switched off. The cleaning operations must be effected before the
loading of the products. In order to guarantee normal operation, the
machine must be installed in areas that the environmental temperature is
between a minimum of +4°C and a maximum of +32°C end humidity of not
over 65%. Must not be installed in places where cleaning is done with water
hoses(ex. big kitchens.).
Do not use water jets to clean the machine.
6.1.1 Procedure for distributor cleaning
Recommended equipment:
For those responsible for filling up and maintenance of the machine the
recommended equipment is as follows:
- Tool carrier case
- Clean uniform
- Disposable gloves
- Roll of kitchen paper
- "Distributor out of action" sign
- damp cloth
- warm water
Never use:
- Sponges, scourers, cloths
- Brushes
- Screwdrivers or metallic objects.
16
Wait washing

Display
Milk circuit
Press and hold P4

Display
Milk washing
Remove the milk pipe
Insert
water container
Press P4
ENGLISH