Publicité
- Place the new sanding belt on the rollers such that
its direction of circulation (arrows on the inside of
the sanding belt) matches the arrows (4) on the
cover. Place the sanding belt first on the drive
shaft and then on the roller on the sanding
attachment (1).
- Replace the cover (3) and tighten the screw (5) by
hand.
- Check the belt run and adjust if necessary (see
Section 7.4).
7.4
Adjusting belt run
Using the screw (2), adjust the sanding belt
(while the machine is not in operation and the
battery pack is removed) so that it runs in the centre
of the sanding belt roller.
1
7.5
Sanding procedure
Switch the machine on first before mounting it on
the workpiece.
Place the machine on the material such that the
sanding belt is parallel to the surface of the
workpiece.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
7.6
Replacing the sanding attachment
See illustration C, page 2.
- Removing the sanding belt (see Section 7.3).
- Remove screw (2), and remove sanding
attachment (1).
- Attach the other sanding attachment as shown
(ensure that the nose at the end of the sanding
attachment is pointing in the direction of the
tensioning arm, see illustration C).
- Secure with screw (2).
- Attaching the sanding belt (see Section 7.3).
- Adjusting the belt run (see Section 7.4).
8. Cleaning, Maintenance
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
9. Troubleshooting
The electronic signal display (15) flashes
and the machine does not start.
The battery pack is empty; the temperature is
too high or the restart protection has triggered.
Switch the machine off and back on again.
The machine will not start if the battery pack is
inserted while the machine is on.
When using a battery pack that is not part of CAS,
the machine will not start.
The electronic signal display (15) is
permanently on.
There has been an overload while working,
therefore the performance may be reduced
temporarily. Reduce working pressure.
Electronic safety shutdown: the machine has
SHUT DOWN by itself. If the slew rate of the
current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing.
10. Tips and Tricks
Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
Order no.: 625367000 4.0Ah (LiHD)
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625549000 10.0 Ah (LiHD)
etc.
Order no.: 625591000 4.0 Ah (LiPOWER)
Order no.: 625028000 5.2 Ah (LiPOWER)
etc.
Chargers: ASC 55, ASC 145, etc.
For a complete range of accessories, see
www.metabo.com or the main catalogue
12. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
ENGLISH en
13
Publicité
