Publicité
en
ENGLISH
* depending on equipment/not in scope of delivery
6. Initial Operation
6.1
Attaching the additional handle
Always work with the additional handle
attached (10)! Attach the additional handle on
the left or right of the machine and secure. Attach
the additional handle to the side facing away from
the sanding belt (6).
6.2
Turning the sanding head (8) to
operating position
Loosen the Quick-release lever (9) using the
hexagon spanner and, if necessary and depending
on the task at hand, turn the sanding head (8). The
sanding head must be positioned in the permitted
working area as shown (see illustration A, page 2).
Firmly tighten the Quick-release lever (9).
Each time before you start work, verify that the
Quick-release lever (9) is sufficiently tightened
to ensure that the sanding head (8) does not move.
Otherwise, the sanding belt (6) may come in contact
with the user. Loss of control can cause personal
injury.
6.3
Dust filter
See illustration D on page 2.
Always fit the dust filter (17) if the surroundings
are heavily polluted.
The machine heats up faster when the dust
filter (17) is fitted. It is protected by the
electronics system from overheating (see Section
9.).
To fit:
Fit the dust filter (17) as shown.
Removal:
Holding the dust filter (17) at the edges, raise it
slightly and then pull it downwards and remove.
6.4
Rotating battery pack
See illustration C on page 2.
The rear section of the machine can be rotated 270°
in 3 stages, thus allowing the machine's shape to be
adapted to the working conditions. Only operate the
machine when it is in an engaged position.
First press the locking button (20), rotate the rear
part of the machine while keeping it pressed.
Release the button while rotating the machine. The
locking mechanism must engage with an audible
"click".
6.5
Battery pack
Charge the battery pack before use (16).
If performance diminishes, recharge the battery
pack.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
"Li-Power" li-ion battery packs have a capacity and
signal indicator: (19)
12
- Press the button (18), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
6.6
Removing and inserting the battery pack
Removal:
Press the battery pack release (13) button and pull
the battery pack (16) forwards.
Inserting:
Slide in the battery pack (16) until it engages.
7. Use
7.1
On/Off switch, continuous activation
Always guide the machine with both hands.
Switch the machine on first before mounting it
on the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits.
After switching off the machine, only place it
down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Switching on/Continuous activation: Push sliding
switch (11) forward. For continuous
activation, now tilt downwards until it
engages.
Switching off: Press the rear end of the slide
switch (11) and release.
7.2
Setting belt speed
The belt speed can be preset via the setting wheel
(14) and is infinitely variable.
Positions 1-6 correspond approximately to the
following belt speeds:
1 ........ 3,0 m/s
2 ........ 4,8 m/s
3 ........ 6,6 m/s
7.3
Sanding belt replacement
See illustration B, page 2.
- Manually loosen screw (5) and remove cover (3).
- Pull tensioner arm (7) backwards and remove
sanding belt (6).
4........8,4 m/s
5........10,2 m/s
6........12,0 m/s
Publicité
