Publicité
24 | English
spindle. The spindle end must not touch the base of the
application tool.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the Off posi-
u
tion when the power supply is interrupted, e.g. when
the battery pack is removed. This prevents uncontrolled
restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Store the application tools inside buildings, in a dry,
u
frost-free room at a uniform temperature.
Remove the application tools before transporting the
u
power tool. This will allow you to avoid damage.
Bonded cutting and grinding discs have an expiration
u
date, after which the discs must no longer be used.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery in the manufacturer's products.
u
This is the only way in which you can protect the battery
against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting metal and stone ma-
terials, plastic and composite materials and for brushing
1 609 92A 9PG | (07.08.2024)
metal and stone materials, roughing metal as well as making
holes in stone materials using diamond annular cutters,
without the use of water. Make sure that the correct protect-
ive guard is used (see "Operation", page 29).
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind stone materials
with diamond grinding heads.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Spindle lock button
(3) On/off switch
(4) Speed preselection thumbwheel
(GWS 18V-11 S)
a)
(5) Rechargeable battery
(6) Rechargeable battery release button
(7) Vibration-damping auxiliary handle (insulated grip-
ping surface)
(8) Standard auxiliary handle (insulated gripping sur-
a)
face)
(9) Extraction guard for grinding
(10) Protective guard for grinding
(11) Protective guard for cutting
(12) Cover for cutting
(13) Mounting flange with O‑ring
a)
(14) Carbide grinding head
a)
(15) Grinding disc
a)
(16) Disc brush (M14)
a)
(17) Cutting disc
a)
(18) Diamond cutting disc
(19) Quick-clamping nut with bar (M14)
(20) Handle (insulated gripping surface)
(21) Grinding spindle
a)
(22) Hand guard
a)
(23) Rubber sanding pad
a)
(24) Sanding sheet
a)
(25) Round nut
(26) Two-pin spanner for clamping nut
a)
(27) Cup brush
a)
(28) Conical brush
a)
(29) Diamond annular cutter
a)
(30) Open-ended spanner
(31) Extraction guard for cutting with cutting guide
a) This accessory is not part of the standard scope of delivery.
a)
a)
a)
a)
Bosch Power Tools
Publicité
