Main Unit Display - Pioneer DJM-900NXS Mode D'emploi

g DIGITAL, CD/LINE, PHONO, LINE, USB */* selector switch (page 13)
Select the input source of each channel from the components connected to this
unit.
h TRIM control (page 13)
Adjusts the level of audio signals input in each channel.
i EQ/ISO (HI, MID, LOW) controls (page 13)
These adjust the sound quality of the different channels.
j Channel Level Indicator (page 13)
Displays the sound level of the different channels before passing through the
channel faders.
k COLOR controls (page 14)
These change the parameters of the SOUND COLOR FX of the different
channels.
l Channel Fader (page 13)
Adjusts the level of audio signals output in each channel.
m CROSS FADER ASSIGN (A, THRU, B) selector switch (page 13)
Set the output destination of each channel to [A] or [B].
n Crossfader (page 13)
Outputs audio signals assigned by the crossfader assign switch correspond-
ing to the curve characteristics selected by [CROSS FADER] (Crossfader Curve
Selector Switch).
o MASTER LEVEL controls (page 13)
Adjusts the sound level output from the [MASTER] channel.
p Master Level Indicator (page 13)
Displays the sound level output from the [MASTER] channel.
q BALANCE controls (page 14)
Adjusts the left/right balance of the sound output from the [MASTER1] termi-
nals, etc.
r MONO, STEREO selector switch (page 14)
Switches the sound output from the [MASTER1] terminals, etc., between mon-
aural and stereo.
s BOOTH MONITOR controls (page 14)
Adjusts the level of audio signals output at the [BOOTH] terminal.
t EQ CURVE (ISOLATOR, EQ) selector switch (page 13)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
u CH FADER (
, ,
Switches the channel fader's curve characteristics.
v CROSS FADER (
,
This switches the crossfader curve characteristics.
w ON/OFF (UTILITY) button
— ON/OFF: Turns the MIDI function on/off (page 16).
— UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 22).
x START/STOP button (page 16)
Sends the MIDI start/MIDI stop signals.
y LFO FORM (WAKE UP) button
— LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI sig-
nal's waveform switches each time the button is pressed (page 19).
— WAKE UP: Cancels the auto standby mode (page 22).
z Main unit display
A X-PAD (page 15)
Adjusts the quantitative parameter of the BEAT EFFECT function.
B BEAT ,
buttons (page 15)
Sets the beat fraction for synchronizing the effect sound.
C TAP (ENTER) button
— TAP: When the BPM measurement mode is set to [TAP], the BPM is input
manually by tapping the button with a finger (page 15).
— ENTER: Used to change this unit's settings (page 22).
D QUANTIZE button
Used to change this unit's settings (page 22).
When the QUANTIZE function is turned on for BEAT EFFECT, the effect is
applied to the sound without going off tempo when the currently playing
track. (page 15).
E AUTO/TAP button (page 15)
Switches the BPM measurement mode.
12
En
) selector switch (page 13)
, ) selector switch (page 13)
F DELAY, ECHO, SPIRAL, REVERB, TRANS, FILTER, FLANGER,
PHASER, ROBOT, MELODIC, SLIP ROLL, ROLL, REV ROLL, SND/RTN
(MIDI LFO) selector switch (page 15)
Switches the BEAT EFFECT effect type.
G 1, 2, 3, 4, MIC, CF.A, CF.B, MASTER selector switch (page 15)
Switches the channel to which the BEAT EFFECT is to be applied.
H TIME control (page 15)
Adjust the BEAT EFFECT's time parameter.
I LEVEL/DEPTH control (page 15)
Adjusts the BEAT EFFECT's quantitative parameter.
J ON/OFF button (page 15)
Turns the BEAT EFFECT function on/off.
Do not pull on the channel fader and crossfader knobs with excessive force. The
knobs are not designed to be removed. Pulling the knobs strongly may result in
damaging the unit.