Fader Start - Denon DN-X400 Mode D'emploi

ENGLISH

FADER START

5
If the separately sold DN-1800F, DN-2100F and DN-2600F players are connected to CH-1 or CH-2, they can be
started using the source input fader (Ch. fader) or Crossfader, as long as the 3.5 mm stereo mini cords have
been connected.
CH1
Fader jack
DN-X400
0 10 ON/OFF MIN MAX
LEVEL GAIN
MIC POST
+10dB
-12dB +12dB ON/OFF -26dB
HI HI 10
8
+10dB 6
-12dB +12dB -26dB
MID MAIN MIC MID 4
3.5 mm stereo
2
+10dB 0
-12dB +12dB -26dB
mini cord LOW LOW
CROSS
FADER
START A
0 10 ON/OFF
LEVEL
AUX MIC
F/S
2
1 3
OFF 4
ON OFF
CH FADER START
ASSIGN A
CROSSFADER
CONTOUR
TRACK M S
OPEN/
CLOSE
T. REMAIN ELAPSED SINGLE CONTINUE
1
SEARCH SCAN
PITCH%
JOG CONT./
MODE SINGLE TIME
TRACK
1
CD1
Fader jack
DN-1800F
8
CH2
Fader jack
L/CUE
LINE1 LINE3 PHONO1/LINE5 PHONO2/LINE7
-20 -15 -10 -7 -5 -3 -1 0 +1 +3 +5 +8 PWR
R/PGM
MIN MAX MIN MAX MIN MAX
LINE2 LINE4 LINE6 LINE8
GAIN GAIN GAIN
MASTER
1 2 3 4
10 10
+10dB +10dB +10dB
-26dB -26dB -26dB 0 10 EFFECT
HI 10 HI 10 HI 10 LEVEL
8 8
LOOP
METER
8 8 8
6 6
MAIN
+10dB 6 +10dB 6 +10dB 6
4 4
-26dB -26dB -26dB
MID 4 MID 4 MID 4 BOOTH
2 2
/ZONE
2 2 2 MIC
0 0
+10dB 0 +10dB 0 +10dB 0
-26dB -26dB -26dB
LOW LOW LOW
CH FADER START CH FADER START CUE
CROSS
FADER
DIGITAL OUT TRACK START B
MARK
CH 1 CH 2 CH 3 CH 4
L-CUE
F/S MONO R-PGM
2
1 3
A B
OFF 4
CUE PGM 0 10
STEREO
PAN CUE/PGM LEVEL
ASSIGN B PHONES
F TRACK M S F
PITCH OPEN/ PITCH
CLOSE
T. REMAIN ELAPSED SINGLE CONTINUE
2
PITCH PITCH
SEARCH SCAN
PITCH BEND PITCH BEND
PITCH%
0% 0%
JOG CONT./
CUE PLAY/PAUSE MODE SINGLE TIME CUE PLAY/PAUSE
TRACK
CUE CUE
REMOTE CONTROL UNIT RC-47
OPEN/CLOSE OPEN/CLOSE
2
1 2
POWER
ON OFF
Channel Fader Start
Turn on the Ch. fader start
switch.
1
Move the source input fader
(Ch. fader) of CH-1 or CH-2
control all the way to the
bottom.
2
3.5 mm stereo
mini cord
DN-1800F
Set the cue point on either drive.
3
DN-2100F and DN-2600F
Set the A-1 or A-2 point on either drive.
When you want to start the
player, move up the source
input fader (Ch. fader) and
the CD player will begin
CD2
4 playing.
Fader jack
NOTES:
• Channels selected with the Crossfader Assign
A, B switches and the Crossfader Start A, B
buttons cannot be started with the source input
fader (Ch. fader).
• Ch. Fader Start and Cross Fader Start for the
same source will not operate simultaneously.
You must select from either one. If both Ch.
Fader and Cross Fader switches are ON, priority
will be the cross fader.
Crossfader Start
Using the Crossfader Assign A B switches,
1
select the channel (CH-1 or CH-2) that the CD
player is connected.
ON OFF
CH FADER START
Press the Crossfader Start A, B buttons of
2
the channel connected to the CD player to be
controlled.
10
8
Slide the Crossfader all the way in direction
opposite the source you want to start. (In the
6
following example, startup is done with the
4
CD player connected to CH-1 set to Assign
2
A. )
3
0
CH FADER START
F/S
2
1 3
A
OFF 4
ASSIGN A
DN-1800F
Set the cue point on the left drive.
4
10
DN-2100F and DN-2600F
Set the A-1 or A-2 point on the left drive.
8
6
Use the Crossfader Contour control to control
5
4
the cross fader startup curve.
2
When the Crossfader is slid in the opposite
0
direction as in "1", CD player play will begin.
CH FADER START
6
F/S
2
1 3
A
OFF 4
ASSIGN A
B
B