Publicité
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These chemicals
may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool into
a liquid.
WARNING: Never clean the machine with the
motor running.
WARNING: DO NOT allow water to splash onto the
battery rail and terminal block area. Wipe all battery interface
components dry.
WARNING: Risk of fire and explosion caused by flammable
substances. For cleaning, do not use any flammable or
aggressive materials.
WARNING: Clean the bottom area of the machine with
only low pressure water, being careful to stay away from
motor, battery port and electronics.
NOTICE: Property damage hazard to the machine
from high pressure water.
iMPORTAnT: Clean the machine daily.
1. Remove the battery.
2. Install the safety cap on the battery plug.
3. Protect the motor well from water.
4. Wipe the machine dry with a clean, dry cloth.
5. Dry any damp spots on the machine that may have
occurred during cleaning.
6. After cleaning, check the cables, wires and screw joints for
leaks, loose connections, chafe marks and other damage and
for contamination of the plug contacts.
Eliminate any problems immediately.
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this product could be hazardous. To reduce
the risk of injury, only D
WALT‑recommended accessories
e
should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Installing and Removing the Wheel Kit (Fig. R)
WARNING: Do not operate the rammer with the wheel
kit installed. The wheel kit should only be used to transport
the rammer.
To Install the Wheel Kit
1. Place the bolts
through the foot of the machine.
20
2. Align the bracket
19
Fig. R.
3. Use a wrench to twist the nuts
clockwise to desired torque.
To Remove the Wheel Kit
1. Use a wrench to twist the nuts of the wheel kit
counterclockwise and remove them from the bolts.
2. Once removed, lift the bracket and the wheel set from
the machine.
WALT. Call 1‑800‑4‑D
e
and the wheel set
18
as shown in
21
of the wheel kit
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
• Only qualified and authorized persons may carry out repairs.
• If the machine should break down, hang a warning sign on
the control arm.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an insurance
loss, such as fire, flood or theft, your registration of ownership
will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account‑login.
Three‑Year Limited Warranty
For warranty terms, go to
www.dewalt.com/support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country‑specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WALT
e
WALT Industrial Tool Co., 701 East
e
English
WALT
e
WALT
e
13
Publicité
