Urmet 1083 Notice page 30

Particular care must be devoted to setting the device codes. Consider the following for correct system
operation:
• Each calling station in the system must have a univocal code (ID) which is set using the dip-switches to
0-3 for main stations and 0-31 for secondary stations. There may be two secondary stations with the
same ID on the same column but with different address (see below for setting the address of a secondary
station, values may be only 0 and 1).
• For secondary calling stations, the ID must coincide with the column ID set on the column interface.
• Each door unit must be characterised by a code (user code) set using dip-switches from 0 to 126 and a
code (apartment station code) set using dip-switches from 0 to 3.
• The apartment station code must be 0 if there is one only station in the apartment.
Up to 4 apartment stations can be connected in parallel: use the same user code and different apartment
•
station codes.
• No two apartments in the same column may have the same user code.
• Each column interface must be characterised by a univocal code (column ID) set using the dip-switches
from 0-31. Secondary door units in the column must have the same ID. All the apartment stations of a
column acquire the column ID from the column interface.
• The column interface is not needed if there is only one column in the system and the column ID apartment
stations will be 0. A column interface for each column is needed if the system has more than one
column.
The interface of all calling stations, apartment stations and columns must start from 0 and be
•
consecutive.
CALLING STATION CONFIGURATION
The calling stations in the system must be univocally identifi ed according to the type. The following
explanation concerns the door unit with buttons mod. Sinthesi. Refer to the corresponding instruction
booklet for other door unit types, e.g. calling module.
ID:
door unit identifi cation
Set a number from 0 to 3 if the door unit is a main unit or from 0 to 31 if the door unit is a secondary unit as
shown in the following fi gure.
• There must not be two main stations with the same ID. Two secondary stations may coexist with the
same ID but with different address (0 or 1).
• The ID of the secondary door unit must coincide with the column ID set in the column interface 1083/50,
if present.
ON DIP
1 2 3 4 5
ID=0
ON DIP
1 2 3 4 5
ID=8
ON DIP
1 2 3 4 5
ID=16
ON DIP
1 2 3 4 5
ID=24
AUX: auxiliary settings
Station type: the door unit can be confi gured either as a main or a secondary device. All the users in the
system may be called from the main door unit. A secondary door unit may only call the users of the column
30
All manuals and user guides at all-guides.com
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=1 ID=2
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=9 ID=10
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=17 ID=18
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=25 ID=26
ID
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=3 ID=4
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=11 ID=12
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=19 ID=20
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=27 ID=28
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=5 ID=6
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=13 ID=14
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=21 ID=22
ON DIP ON DIP
1 2 3 4 5 1 2 3 4 5
ID=29 ID=30
ON DIP
1 2 3 4 5
ID=7
ON DIP
1 2 3 4 5
ID=15
ON DIP
1 2 3 4 5
ID=23
ON DIP
1 2 3 4 5
ID=31
DS1083-029E