Eaton Tripp Lite Serie Mode D'emploi page 67

5 5 . . 2 2 S S t t o o r r a a g g e e
The ideal ambient temperature range is 5°F to 122°F (-15°C to 50°C). It is recommended to charge the UPS for
at least eight hours, then store the UPS covered and upright in a cool, dry location. Remove any accessories
and disconnect any cables connected to the UPS to avoid unnecessary draining of the battery.
E E x x t t e e n n d d e e d d S S t t o o r r a a g g e e
During extended storage in environments where the ambient temperature is 5°F to 86°F (-15°C to 30°C),
charge the UPS battery every six months.
During extended storage in environments where the ambient temperature is 86°F to 113°F (30°C to 45°C),
charge the UPS battery every three months.
5 5 . . 3 3 R R e e c c y y c c l l i i n n g g U U s s e e d d E E q q u u i i p p m m e e n n t t
Contact your local recycling or hazardous waste center for information regarding proper the disposal of used
equipment.
5 5 . . 4 4 T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g
The Tripp Lite Series Smart Tower UPS system has an audible alarm feature to alert you of potential power
problems. When activated, the alarm sounds at different intervals according to a particular condition. Use
Table 7 to determine and resolve the UPS alarms and conditions. See for the various LCD/LED indicators and
alarms tones that can be active on the UPS.
Table 7. Troubleshooting
Problem
No LEDs are displayed on
the front panel, or the LCD
is not illuminated
The UPS is always in
battery mode
The UPS alarm sounds
continuously
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of
electric shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the
trash. This product contains sealed, lead— acid batteries and must be disposed of
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead‐acid batteries and must be
properly. For more information, contact your local recycling/reuse or hazardous waste
disposed of properly. For more information, contact your local recycling/reuse or
center.
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
hazardous waste center for more information.
Eaton, Powerware, and BladeUPS are registered trademarks of Eaton Corporation or its subsidiaries and affiliates.
Phillips and Pozidriv are registered trademarks of Phillips Screw Company.
Possible Cause
ECopyright 2008–2010 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
The UPS is not turned on
Battery Voltage is to too low
Battery fault
The power cord is disconnected
Overload in Line mode
Output short fault
Eaton Tripp Lite Series Cloud-Connected UPS Systems User Guide 9349D0—Rev A
Solutions
Verify that the UPS is connected to a valid power source and
press the power button again.
Charge the battery for at least six hours.
Replace the battery.
Verify that the UPS is connected to a valid power source.
Remove any unnecessary load and verify that the load does not
exceed the defined UPS specifications. If the problem persists,
contact Eaton support.
Turn the UPS off, disconnect the UPS from the input AC power
source, and remove the load equipment. Check the equipment for
potential issues. Turn the UPS on ( see
plug the load equipment back in, one at a time. If the problem
persists, contact Eaton support.
Storage
2.4 Turning the UPS On)
61