Honeywell HCE300 Serie Manuel D'instructions page 3

SET UP
The Honeywell Ceramic Tower Heater requires no assembly. Simply unpack heater and save all packaging
materials for off-season storage.
Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away from any wall
or combustible material.
DO NOT use on an unstable surface such as bedding or deep carpeting.
BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE A TRIPPING HAZARD.
MOVING THE HEATER
This heater is equipped with a Cool Touch handle for your convenience.
Turn off the heater.
Allow it to cool for ten minutes.
Unplug heater and move.
OPERATION
NOTE: Never leave an operating unit unattended.
• With heater in the OFF position , plug the heater
into a polarized 120V outlet. DO NOT FORCE THE
POLARIZED PLUG INTO THE OUTLET; it will only fit
one way.
• With 80° oscillation, the Honeywell Ceramic Tower
Heater is versatile and designed to be placed in the
center of the room or closer to the wall (at least 3 feet
way) for maximum convection room heating.
• Turn heater on by pressing the Power Button
Power Indicator will illuminate and the heater will start
in the Constant On HI Level Setting .
• The heater has two operational modes – continuous heating
or heating with a thermostat setting where the heater cycles on and off according to the selected temperature setting.
• To set a Continuous Heat Setting, press : - Choose Low to use up to 900 watts of power
- Choose High to use up to 1500 watts of power
NOTE: The Low setting does not require as much electricity to operate, it is more energy efficient and may be a
better option if you are concerned about saving energy.
• In the continuous heat mode, make sure to manually turn the heater OFF when done using this appliance.
• To set the Thermostat, press the Thermostat Control Buttons
Desired Temperature will flash five times and then the Current Temperature in the room will display as a steady
red. On the HCE305/HCE309 unit models only, there are 4 pre-set comfort settings from which to choose: 65°,
70°, 75°, 80°. These are your desired room temperature settings.
NOTE: If the Current Temperature is higher than your Desired Temperature, the heater will be off until the room
temperature falls below this setting or until the Desired Temperature is changed.
• Press the Timer Button to select 1, 2, 4, or 8 hour setting. The heater will run for that chosen period in the selected
mode, counting down the hours and automatically shutting the heater off after the selected time has passed.
• If unit has an oscillation feature, press the Oscillate Button
• To shut the heater off, press the Power Button
off after counting down 6 seconds in the Temperature Display to cool down the internal components.
• It is important to allow the heater to run through the cool down phase. DO NOT unplug the heater until it has
completed the cool down cycle.
1
Current Temperature/
Desired Temperature Display
Power
Indicator
Power
Button
. The
Heat Level Settings
Oscillate Button
NOTE: Controls/features will vary slightly by model
(up to 750 watts on the HCE317 Series only)
and choose your Desired Temperature. The
to turn on or off the oscillation function.
and the heater will begin Powering Down. The heater will shut
4
SAFETY FEATURES
The Honeywell Ceramic Tower Heater is equipped with several devices and features for added protection:
A 360° tip-over switch that disables the heater if it is tipped in any direction.
A high temperature safety sensor prevents overheating.
A thermal cut-off fuse will permanently shut down the heater should it operate at a higher than normal temperature.
High temperature plastic.
Cool to touch housing and handle.
Thermal insulated wiring for heat resistance and reinforced wire connection help protect against loose
connections.
HCE323/HCE353 Series only also has a Safeguard™ Motion Sensor that shuts the heater off if an object gets too
close to the motion sensor.
SAFEGUARD™ MOTION SENSOR (HCE323/HCE353 SERIES ONLY)
The Honeywell Safeguard™ Motion Sensor Digital Tower (Model series HCE323/HCE353 only) is equipped with
an additional safety feature. If an object is placed too close to the heater, the Motion Sensor Light (Fig. 2) will blink
to warn you that there is an obstruction. If the object is not removed, the sensor will disable the heater, turning the
heater off until the object is removed. The heater will restart after a few seconds once the object is removed.
Timer
Press the Safeguard™ Motion Sensor Button
2
Thermostat
Control Buttons
Safeguard™ Motion Sensor Light
REMOTE CONTROL (HCE323/HCE353 SERIES ONLY)
The Honeywell Safeguard™ Motion Sensor Ceramic Digital Tower Heaters can be completely controlled with the
remote. This remote uses a button cell type battery which comes included in the remote.
To activate the battery, simply pull the plastic tab.
Place remote control in the holder in the back of the heater when not in use.
This product contains batteries, please do not dispose of them in a landfill, check local recycling.
FAHRENHEIT TO CELSIUS
Press and hold both Thermostat Control Buttons
NOTE: The Remote will not change between Fahrenheit and Celsius - only the controls on the heater.
For the HCE305 and HCE309 units, there is no option to change Fahrenheit and Celsius.
(Fig. 3) to turn on or off this feature.
3
Safeguard™ Motion Sensor Button
for three seconds to change between Fahrenheit and Celsius.
5