Publicité
˜ Getting started
Attaching the hoses
1. Remove the protective caps
2. Straighten the suction hose (Ø 6 mm)
(Transparent)
and the drain hose
[
9 ]
(Ø 12 mm) (Grey)
3. Put the hose clamp
suction hose (Ø 6 mm) (Transparent)
Plug the suction hose end onto the suction
hose connector
. Fasten the hose clamp
[
8 ]
(Tool: Slotted screwdriver or SW6 wrench).
4. Put the hose clamp
drain hose (Ø 12 mm) (Grey)
end of the drain hose onto the drain hose
connector
. Fasten the hose clamp
6 ]
[
(Tool: Slotted screwdriver or SW6 wrench).
5. Pay attention to the pumping direction
on the appliance.
m
Make sure that the hoses
straightened to avoid damage.
˜ Operation
1. Start the vehicle and run it for 5–10 minutes
to warm up the oil (60 °C is the maximum oil
temperature). This reduces viscosity of the oil
and enables to pump it out more efficiently.
m
Do not pump the oil when the car
engine is running.
2. Gently insert the suction hose (Ø 6 mm)
(Transparent)
into the bottom of the oil pan
[
9 ]
(e.g. by the oil level test opening).
3. Insert the drain hose (Ø 12 mm) (Grey)
into a container (e.g. oil collecting tray).
4. Set the on/off switch
5. Connect the positive pole clamp (red)
the positive pole (+) of the vehicle battery.
6. Connect the negative pole clamp (black)
the negative pole (‒) of the vehicle battery.
7. Turning on: Set the on/off switch
position. The pumping begins after a short
suction period.
8. Turning off: Set the on/off switch
Turn the appliance off as soon as oil extraction
is over or after 30 minutes of continuous
operation.
22 GB/IE
(fig. A).
7 ]
[
.
11 ]
[
to the end of the
[
10 ]
.
[
9 ]
to the end of the
10 ]
[
. Plug the
[
11 ]
[
10 ]
are
9 ]
[
11 ]
[
11 ]
[
to "O" (off) position.
[
1 ]
to
4 ]
[
5 ]
[
to "I"
[
1 ]
to "O".
[
1 ]
9. After each use, pump through some fresh oil to
clean the appliance.
10. Remove the negative pole clamp (black)
from the negative pole (‒) of the vehicle
battery.
11. Remove the positive pole clamp (red)
the positive pole (+) of the vehicle battery.
m
To prevent damage, let the appliance
cool for at least 10 minutes after
every 30 minutes of continuous
[
10 ]
operation.
12. Change the oil filter and refill with new oil
according to the vehicle instructions.
13. Used oil needs to be disposed of in a way
according to "Disposal".
˜ Cleaning and maintenance
m
WARNING! During cleaning or operation,
do not immerse the electrical parts of the
appliance in water or other liquids. Never hold
the appliance under running water.
Cleaning
1. After each use, pump through some fresh oil to
clean the appliance.
2. Clean both clamps
after each use. Make sure there is no adhering
battery fluid left on the appliance.
3. Keep the casing
Do not use abrasive, aggressive or chemical
cleaning agents to clean the surface of the
appliance.
4. In case of oil spillage, clean it with a soft cloth
or a paper towel.
Maintenance
Check the hose clamps
to
Before each use check the appliance and all its
accessories for any visible damage.
Apart from the occasional cleaning, the
appliance is maintenance-free.
Storage
When not in use, store the cleaned appliance
in a dry, secure location away from children.
Store used oil/diesel in appropriate containers
only.
4 ]
[
with a dry cloth
4 ]
[
5 ]
[
and accessories clean.
2 ]
[
for tight fit.
10 ]
[
5 ]
[
from
Publicité
