Télécharger Imprimer la page

Publicité

Liens rapides

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22, ANSI Z21.50 FOR VENTED GAS FIREPLACES.
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
SAFETY INFORMATION
WARNING
!
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
If the information in these instructions
are not followed exactly, a fi re or
explosion may result causing property
f i r e - p a r t s . c o m
damage, personal injury or loss of life.
- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbour's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the
fi re department.
- Installation and service must be performed by a
qualifi ed installer, service agency or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certifi ed kit is used.
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com
$10.00
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
INSTALLATION AND
GDI-30GN
NATURAL GAS
GDI-30GP
WARNING
!
PROPANE
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
1.28C
W415-0832 / C / 06.07.12
1

Publicité

loading

Sommaire des Matières pour Napoleon GDI-30GN

  • Page 1 NEVER ALLOW CHILDREN TO TOUCH GLASS. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com $10.00...
  • Page 2 TABLE OF CONTENTS INSTALLATION OVERVIEW INTRODUCTION DIMENSIONS MINIMUM CLEARANCE TO COMBUSTIBLES GENERAL INSTRUCTIONS GENERAL INFORMATION RATING PLATE INFORMATION INSTALLATION INSERT LEVELLING CHIMNEY CONNECTION GAS INSTALLATION OPTIONAL WALL SWITCH / THERMOSTAT FRAMING MINIMUM MANTEL CLEARANCES FINISHING 4 SIDED SURROUND DOOR REMOVAL AND INSTALLATION MEDIA TRAY INSTALLATION MEDIA INSTALLATION LOGO PLACEMENT...
  • Page 3 1.0 INSTALLATION OVERVIEW Door, see “FINISHING - DOOR REMOVAL AND INSTALLATION” section. Venting, see “INSTALLATION - CHIMNEY CONNECTION” section. f i r e - p a r t s . c o m Surround, see “FINISHING - 4 SIDED SURROUND” section. Rating Plate, see “RATING PLATE INFORMATION”...
  • Page 4 2.0 INTRODUCTION WARNING • THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED. • ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED. • Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fi...
  • Page 5 DIMENSIONS 3” Ø COLLARS 27 ½” ” ” 25 ½” ” ” ” ” 13 ¾” ” 13 ¾” ” ” 7 ¼” 42” MINIMUM CLEARANCE TO COMBUSTIBLES This appliance must be recessed into a vented noncombustible solid fuel burning appliance (prefabricated or masonry) only.
  • Page 6 The installation must conform with local codes or, in absence of local codes, the National Gas and Propane We suggest that our gas Installation Code CSA B149.1 in Canada, or the National hearth products be installed Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States.
  • Page 7 LONGUEURS VERTICALES MINIMALES ET MAXIMALES SONT 10 PIEDS ET 35 PIEDS RESPECTIVEMENT. LONGUEURS VERTICALES NGUEURS V f i r e - p a r t s . c o m WOLF STEEL LTD. 24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 0G8 CANADA TARIO L TARIO GDI/CDI-30G W385-0492 / C INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to the model, venting and gas type of the appliance.
  • Page 8 3.0 INSTALLATION WARNING RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE. Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have any repair work done by a qualifi...
  • Page 9 2" or 3" diameter liner for intake and one 3" diameter liner for exhaust. The minimum and maximum vent lengths are 10 and 35 feet respectively. Recommended Napoleon kits come in 3 lengths: 1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST & 2-3" TO 2" REDUCER:...
  • Page 10 GAS INSTALLATION WARNING RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS SPARKS OR OPEN FLAMES. SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE. ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH THE GLASS DOOR OPENED OR REMOVED.
  • Page 11 4.0 FRAMING WARNING MINIMUM CLEARANCE TO COMBUSTIBLES MUST BE MAINTAINED OR A SERIOUS FIRE HAZARD COULD RESULT. NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE. This insert must be recessed into a vented noncombustible wood-burning appliance (prefabricated or masonry) only. The minimum appliance opening size in which the appliance is to be installed is: HEIGHT 22"...
  • Page 12 5.0 FINISHING WARNING ENSURE THE UNIT IS COMPLETELY COOL BEFORE STARTING INSTALLATION. 4 SIDED SURROUND LIGHT SWITCH ON/OFF SWITCH Connect the two black on/off switch wires f i r e - p a r t s . c o m SHOULDER (already connected to the SCREWS...
  • Page 13 MEDIA TRAY INSTALLATION Secure the media tray to the burner using 6 screws (W570-0001). When removing the media tray make sure the glass media are away from the center of the screen, exposing the burner, remove screws and lift media tray out. When replacing burner, absolutely no glass media can be in cup surrounding the orifi...
  • Page 14 6.0 REPLACEMENT BLOWER INSTALLATION WARNING RISK OF FIRE AND ELECTRICAL SHOCK. TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE. USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
  • Page 15 7.0 OPERATION WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH THE GLASS DOOR OPENED OR REMOVED.
  • Page 16 ANTI CONDENSATION SWITCH This appliance has the option to go from an electronic intermittent pilot ignition (IPI) to a standing pilot for cold climates. The anti condensation control switch (standing pilot) is located on the left of the control panel. Using your fi...
  • Page 17 NIGHT LIGHT WIRING DIAGRAM f i r e - p a r t s . c o m W415-0832 / C / 06.07.12...
  • Page 18 9.0 ADJUSTMENTS PILOT BURNER ADJUSTMENT Adjust the pilot screw to provide properly sized fl ame. Turn in a clockwise direction to reduce the gas fl ow. Check Pressure Readings: Inlet pressure can be checked by turning screw (A) counter- clockwise 2 or 3 turns and then placing pressure gauge tubing over the test point.
  • Page 19 VENTURI ADJUSTMENT WARNING THE FRONT OF THE APPLIANCE BECOMES VERY HOT DURING OPERATION. LET THE APPLIANCE COOL COMPLETELY BEFORE CONDUCTING SERVICE. AIR SHUTTER ACCESS PLATE This appliance has an air shutter that GDI-30G has been factory set open according to the chart below: 1/4"...
  • Page 20 10.0 MAINTENANCE MAINTENANCE MAINTENANCE WARNING MAINTENANCE TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE. APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED. DO NOT USE ABRASIVE CLEANERS. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
  • Page 21 10.2 LAMP ASSEMBLY REPLACEMENT WARNING THE FRONT OF THE APPLIANCE BECOMES VERY HOT DURING OPERATION. LET THE APPLIANCE COOL COMPLETELY BEFORE CONDUCTING SERVICE. Remove the glass media and media tray, see "MEDIA TRAY INSTALLATION" section. Remove the 2 screws holding the lamp assembly shield. Compress the 3 retainer fi...
  • Page 22 10.4 CARE OF GLASS WARNING DO NOT CLEAN GLASS WHEN HOT! DO NOT USE ABRASIVE CLEANERS TO CLEAN GLASS. HOT GLASS WILL Buff lightly with a clean dry soft cloth. Clean both sides CAUSE BURNS. of the glass after the fi rst 10 hours of operation with a DO NOT TOUCH GLASS recommended fi...
  • Page 23 PROPANE GAS PILOT ASSEMBLY W690-0002 THERMAL SENSING SWITCH W660-0009 BURNER ON/OFF SWITCH W455-0069 NATURAL GAS PILOT INJECTOR W455-0068 PROPANE GAS PILOT INJECTOR W385-0334 NAPOLEON LOGO W562-0008 GLASS GASKET KB-35 VARIABLE SPEED SWITCH W010-1095 GLASS W/ GASKET W010-1042 DOOR, GLASS & GASKET ASSEMBLY W100-0112...
  • Page 24 ACCESSORIES REF NO. PART NO. DESCRIPTION ON / OFF REMOTE THERMOSTAT REMOTE GD-660 REMOTE WALL SWITCH WITH 20" WIRE W660-0026 TIMER, BATTERY OPERATED GI-RB RISER BOX - PAINTED BLACK W175-0322 CONVERSION KIT - LP-NG f i r e - p a r t s . c o m W175-0323 CONVERSION KIT - NG-LP W415-0832 / C / 06.07.12...
  • Page 25 12.0 TROUBLESHOOTING WARNING ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT, WITH THE GLASS DOOR OPEN OR REMOVED. TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE. APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED. DO NOT USE ABRASIVE CLEANERS.
  • Page 26 SYMPTOM PROBLEM TEST SOLUTION Carbon is being Air shutter has become Ensure air shutter opening is free of lint or other deposited on blocked. obstructions. glass, logs, Flame is impinging on the Check that the glass, logs, rocks or media are rocks, media glass, logs, rocks, media correctly positioned.
  • Page 27 SYMPTOM PROBLEM TEST SOLUTION White / grey fi lm Sulphur from fuel is being Clean the glass, see “CARE OF GLASS” section forms. deposited on glass, logs or DO NOT CLEAN GLASS WHEN HOT. combustion chamber If deposits are not cleaned off regularly, the glass surfaces.
  • Page 28 All parts replaced under the President’s Limited Lifetime Warranty Policy are subject to a single claim. During the fi rst 10 years NAPOLEON® will replace or repair the defective parts covered by the lifetime warranty at our discretion free of charge. From 10 years to life, NAPOLEON®...
  • Page 29 14.0 SERVICE HISTORY f i r e - p a r t s . c o m 43.1 W415-0832 / C / 06.07.12...
  • Page 30 15.0 NOTES f i r e - p a r t s . c o m 44.1 W415-0832 / C / 06.07.12...
  • Page 31 f i r e - p a r t s . c o m 44.1 W415-0832 / C / 06.07.12...
  • Page 32 f i r e - p a r t s . c o m W415-0832 / C / 06.07.12...
  • Page 33 f i r e - p a r t s . c o m...
  • Page 34 f i r e - p a r t s . c o m...
  • Page 35 f i r e - p a r t s . c o m...
  • Page 36 f i r e - p a r t s . c o m...
  • Page 37 f i r e - p a r t s . c o m...
  • Page 38 f i r e - p a r t s . c o m...
  • Page 39 f i r e - p a r t s . c o m...
  • Page 40 f i r e - p a r t s . c o m...
  • Page 41 f i r e - p a r t s . c o m...
  • Page 42 f i r e - p a r t s . c o m...
  • Page 43 f i r e - p a r t s . c o m...
  • Page 44 f i r e - p a r t s . c o m...
  • Page 45 CONTRÔLE NUMÉRIQUE DU BRÛLEUR f i r e - p a r t s . c o m...
  • Page 46 f i r e - p a r t s . c o m...
  • Page 47 f i r e - p a r t s . c o m...
  • Page 48 f i r e - p a r t s . c o m...
  • Page 49 f i r e - p a r t s . c o m...
  • Page 50 f i r e - p a r t s . c o m...
  • Page 51 f i r e - p a r t s . c o m...
  • Page 52 f i r e - p a r t s . c o m...
  • Page 53 f i r e - p a r t s . c o m...
  • Page 54 f i r e - p a r t s . c o m...
  • Page 55 f i r e - p a r t s . c o m...
  • Page 56 f i r e - p a r t s . c o m...
  • Page 57 f i r e - p a r t s . c o m...
  • Page 58 f i r e - p a r t s . c o m...
  • Page 59 f i r e - p a r t s . c o m...
  • Page 60 f i r e - p a r t s . c o m...

Ce manuel est également adapté pour:

Gdi-30gp