Maintenance And Service; Maintenance And Cleaning; Accessories; Warranty And Service - Trumpf TruTool N 160 E Instructions De Montage

Lubricating/Cooling the Punch
To extend the service life of the punch 3, a lubricating
agent with good cooling properties (e.g. cutting oil)
should be used.
Apply a trail of lubricant beads onto the top side of the
metal sheet alongside the intended cutting line. For
long periods of continual use or for work with high fric-
tional wear (e.g. when cutting aluminium), the cutting
head should be immersed into a container with lubri-
cant in regular intervals.
Cutting along a Cutting Mark or with a Guide
Straight cuts are carried out easier when the machine
is guided alongside a rule.
Contours can be cut by guiding the machine along a
template.
For inside cuts, pre-drilling a hole with a diameter of
21 mm is necessary.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep
the machine and ventilation slots clean.
Clean and lubricate the punch 3 and die 5 every
3 operating hours.
Change the punch and die in good time when worn.
Only sharp tools produce a good cutting quality and
make the machine last longer.
The punch 3 and the die 5 may not be reground.
Changing the Die
Unscrew the knurled screw 7 of the die holder 4. Take
out the die 5.
Il necessary, clean the die holder 4.
Put a new, well greased die 5 into the die holder. Pay
attention to the alignment of the flat side.
Tighten the knurled screw 7 again, the rubber ring
placed onto it 6. Tighten the screw against the resist-
ance of the rubber ring.
Changing the Punch
Loosen the screw 2 and pull the die holder und 4 com-
pletely out of the housing.
Push the punch 3 laterally out of the slot in the die
holder 4 and pull it down and out.
Place a new, well greased punch 3 into the slot in the
die holder 4 and align it centrally.
3 609 929 B93 • 2.8.10
Push the die holder 4 with caution over the punch 3
back into the housing. Turn the die holder into one of
the three possible positions (see "Changing the Cut-
ting Direction", page 8). Tighten the screw 2.

Accessories

Die 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0141714
Die for sheet thickness up to 1 mm . . . . . . 0931611
Punch 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0117676
Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . 0950316

Warranty and Service

For TRUMPF power and pneumatic tools, a liability
period of 12 months applies from the invoice date on.
Damage attributable to normal wear, overloading or
improper handling of the machine will be excluded
from the warranty. Damage due to material or manu-
facturing defects will be corrected free-of-charge by
replacement or repair. Claims can only be accepted
when the machine is sent undisassembled to your
TRUMPF Service Centre.
The address of your TRUMPF representative can be
found under:
www.trumpf-powertools.com
Disposal
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Do not dispose of power tools into household waste!
Only for EC countries:
According to the European Guideline
2002/96/EC for Waste Electrical and
Electronic Equipment and its imple-
mentation into national right, power
tools that are no longer usable must be
collected separately and disposed of
in an environmentally correct manner.
Subject to change without notice.
English | 9