Hitachi PC-ARFP1E Manuel D'utilisation page 34

TEST RUN MENU
6.3 THERMISTOR SELECTION
This function changes the temperature thermistor from indoor
unit thermistor to thermistor of remote control switch or an
average between both temperatures.
1 Press and hold " " (menu) and "
simultaneously for at least 3 seconds during the normal
mode (when unit is not operated). The test run menu will be
displayed.
Test Run Menu
Test Run
Function Selection
Thermistor Selection
Input/Output
Function 5
Sel.
2 Select "Thermistor Selection" from the test run menu and
press "OK".
3 Change the temperature thermistor item by pressing "
and press "OK". Select between Remote, Average or IDU.
6.4 INPUT/OUTPUT SELECTION
1 Press and hold " " (menu) and "
simultaneously for at least 3 seconds during the normal
mode (when unit is not operated). The test run menu is
displayed then.
2 Select "Input/Output" from the test run menu and press "OK".
Test Run Menu
Test Run
Function Selection
Thermistor Selection
Input/Output
Function 5
Sel.
3 Select the indoor unit by pressing "
(This screen is NOT displayed when the number of indoor
units connected with the remote control switch is 1. In this
case, go directly to the step 4).
Input/Output Selection
01-01
01-02
01-03
01-04
Sel.
4 Press " " and select the item.
Input/Output:01-03
Item Setting
Input 1
Input 2
Output1
Output2
Output3
Sel.
Adj.
26 PMML0496 rev.1 - 12/2020
/
?
" (return / help)
01
/
03
OK
Entr Rtrn
ADJ
/
?
" (return / help)
01
/
03
OK
Entr Rtrn
ADJ
" and press "OK".
All
OK Entr Rtrn
Connector
00 CN3 1-2
00 CN3 2-3
00 CN7 1-2
00 CN7 1-3
00 CN8 1-2
Entr Rtrn
OK
Thermistor Selection
Thermist.
LOUV.
T-RUN TIME
Adj.
4 Select "Yes" and press "OK". The test run menu will be
displayed after the setting is confirmed. If "No" is pressed,
the screen will return to step 3.
Thermistor Selection
Confirm setting of thermistor
selection?
"
Sel.
5 Press " " (return / help) on the test run menu to return to the
normal mode.
5 Press " " and change the setting.
Input/Output:01-03
Item
Output2
Input 2
Output1
Input 1
Output3
Sel.
6 Press "OK", then the confirmation screen is displayed.
7 Select "Yes" and press "OK". The test run menu is displayed
after the setting is confirmed. If "No" is pressed, the screen
returns to step 4.
Input/Output:01-03
Confirm setting of
input/output?
Sel.
/ ?
8 Press " " (return / help) on the test run menu to return to
the normal mode.
?
N O T E
To set other units, press "
screen returns to step 3 (If the number of indoor units connected with the
remote control switch is 1, the screen returns to step 4).
IDU
120MIN
OK Entr Rtrn
Yes No
OK
Entr Rtrn
Setting Connector
00 CN7 1-3
00 CN3 2-3
00 CN7 1-2
00 CN3 1-2
00 CN8 1-2
Entr Rtrn
OK
Adj.
Yes No
OK
Entr Rtrn
/ " (return / help) at steps 4 and 5 so that the
?