Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0439
  6. Instructions de montage

R&G CP0439 Instructions De Montage

Masquer les pouces
1
2
3
4
5
6
7

Publicité

Liens rapides

Télécharger ce manuel
Page 1 of 7
CP0439
FITTING INSTRUCTIONS CP0439 AERO CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0439

Sommaire des Matières pour R&G CP0439

  • Page 1 Page 1 of 7 CP0439 FITTING INSTRUCTIONS CP0439 AERO CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
  • Page 2 Page 2 of 7 CP0439 TOOLS REQUIRED GENERAL TORQUE SETTINGS 14mm & 19mm A/F SOCKET & WRENCH M4 BOLT = 8Nm • M5 BOLT = • TORQUE WRENCH (UP TO 50Nm) M6 BOLT = SUITABLE SUPPORT JACK • M8 BOLT = 20Nm...
  • Page 3 Page 3 of 7 CP0439 LHS & RHS EXPLODED ASSEMBLY VIEW FITTING PICTURES Picture 1 Picture 2 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting.
  • Page 4 Page 4 of 7 CP0439 Assemble the crash protectors before removing the engine bolts to limit the amount of time the engine is partially un-supported. Following the assembly diagram place the M10 washers (ITEM 8) over the bolts (ITEMS 5 & 6) •...
  • Page 5 Page 5 of 7 CP0439 NOTICE DE MONTAGE POUR CP0439BL PROTECTIONS CRASH YAMAHA MT 09 2018- PHOTO A PHOTO B ARRIÈRE MOTO AVANT MOTO PHOTO C E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS...
  • Page 6 Page 6 of 7 CP0439 GAUCHE DROITE OUTILS REQUIS Clé à cliquet + douille 17mm. • Clé à cliquet + douille 8mm. • • Clé dynamométrique (jusqu’à 50Nm). LÉGENDE ARTICLE 1 = BC0002 CAPUCHONS DE PROTECTION CRASH (x2). ARTICLE 2 = B0063 avec CS066 (10mm) (PROTECTIONS CRASH) (x2).
  • Page 7 Page 7 of 7 CP0439 plus pour que vous sentiez la compression augmenter légèrement. Appliquez ensuite un quart de tour. Serrez à 40 Nm de couple (ne dépassez pas ce chiffre, car des dommages peuvent survenir à la moto et au boulon).