Publicité
Preparation
1.
Wear safety glasses at all times while operating the machine.
Hearing protection is also recommended, especially for
extended operating periods.
2.
Avoid wearing any loose-fitting clothing or that has hanging
cords or ties.
3.
Before starting the machine, check that all screws, nuts, bolts
and other fasteners are properly secured. Replace damaged or
unreadable warning and operating decals.
4.
Warning
Use extra care in handling fuels. They are flammable and
the vapours are explosive.
a)
Use only an approved container for fuel.
b)
Never remove fuel cap or add fuel with engine
running. Allow engine to cool before refuelling. Do not
smoke while refuelling.
c)
Never refuel the machine indoors.
d)
Never store the machine or fuel container inside
where there is an open flame such as a water heater.
e)
Always replace & securely tighten the fuel cap after
refilling.
f)
If fuel is spilled, do not attempt to start the engine,
but move the machine away from the area of spillage
before starting.
g)
If the fuel tank is drained, this should be done
outdoors.
Operating Safety
OPERATION
1.
When feeding shreddable material into the equipment, be
extremely careful that pieces of metal, rocks, bottles, cans or
other foreign objects are not included.
2.
If the cutting mechanism strikes any foreign objects or if the
machine should start making any unusual noise or vibration,
immediately shut off the engine and allow the machine to stop.
Disconnect the spark plug and take the following steps:
1) Inspect for damage
2) Replace or repair any damaged parts with equivalent
specifications
3) Check for and tighten any loose parts
Do not attempt to repair the machine unless you are
competent to do so.
3.
Keep the engine clean of debris and other accumulations to
prevent damage to the engine or possible fire.
4.
Keep all guards and deflectors in place and in good working
condition.
5.
Always stand clear of the discharge area when operating this
machine.
6.
Keep your face and body away from the feed & discharge
openings.
7.
Do not over-reach. Never stand at a higher level than the base
of the machine when feeding material into it. Keep proper
balance and footing at all times.
8.
Do not allow processed material to build up in the discharge
zone; this may prevent proper discharge and can result in
kickback of material through the feed intake opening.
9.
If the machine becomes clogged at the inlet opening or
discharge chute shut off the power source and disconnect
the spark plug wire before clearing debris in the inlet opening
or discharge chute. Remember that operating the starting
mechanism on engine powered machines will still cause
the cutting means to move.
10. Do not tamper with the engine governor settings on the
machine: the governor controls the maximum safe operating
speed and protects the engine and all moving parts from
damage caused by overspeed. Seek authorised service if a
6
536672.A.0 - Masport European Chipper Owner's Manual
problem exists.
11. Do not rotate the chipper disc by hand without first
disconnecting the spark plug
MAINTENANCE AND STORAGE
1.
When this equipment is stopped for servicing, inspection,
or storage, or to change an accessory, make sure the spark
plug wire is disconnected from the spark plug. Make sure that
all moving parts have come to a complete stop. Allow the
machine to cool before making any inspections, adjustments
etc. Maintain the machine with care and keep it clean.
2.
Store the machine out of reach of children and where fuel
vapour will not reach an open flame or spark. For extended
storage periods, run the unit dry of petrol. Always allow the
machine to cool before storing.
3.
When servicing the cutting means be aware that, even though
the power source will not start due to the interlock feature of
the guard, the cutting means can still be moved by a manual
starting mechanism.
Starting
1.
Ensure the chipper is on stable, level ground so it won't tip
over.
2.
Do not discharge chipped material on hard surface as it will
rebound and may cause damage to people or property.
3.
Make sure people and pets are clear of the operating area.
4.
Refer to your engine booklet for details on adding oil and fuel to
your engine
5.
Make sure the actuation lever is in the disengage position
before starting
6.
Follow the instructions to Turn switch to "on" position, turn fuel
tap open, throttle to fast and choke the engine (if it is cold).
7.
Pull the starting cord until the engine starts and open the choke
after 5 seconds.
8.
For the electric start model, turn the key as instructed in the
engine manual
9.
Adjust the throttle to achieve maximum operating speed.
10. Once the engine is hot it is not necessary to use the choke
when restarting.
11. Slowly pull the actuation lever to engage the belts and cutting
disc. (A fast engagement action will stall the engine.)
12. Do not restart the unit with material in the inlet chute. The
additional drag may cause severe wear on the drive belt or you
may damage the pull starter on the engine.
Note: STOPPING Disengage the actuation lever, move
the throttle to slow and turn the switch to "off".
Chipping
Warning
A. Wear eye protection.
B. Never put your hands or fingers in the chipper chute. For the
Publicité
