Publicité
Owner's manual
CLEANING AND MAINTENANCE
Important:
Before cleaning, make sure the cooking zones are switched o and
•
that the residual heat indicator ("H") is not displayed.
•
Do not use abrasive sponges or scouring pads as they may damage the
glass.
•
After each use, clean the hob (when it is cool) to remove any deposits and
stains from food residue.
•
A surface that is not kept suitably clean may reduce the sensitivity of
control panel buttons.
•
Use a scraper only if residues are stuck to the hob. Follow the scraper
manufacturer's instructions to avoid scratching the glass.
•
Sugar or foods with high sugar content can damage the hob and must be
immediately removed.
•
Salt, sugar and sand could scratch the glass surface.
•
Use a soft cloth, absorbent kitchen paper or a special hob cleaner (follow
the Manufacturer's instructions).
•
Spills of liquid in the cooking zones can cause the pots to move or vibrate.
•
After cleaning the hob, dry thoroughly.
TROUBLESHOOTING
•
Check that the electricity supply has not been shut o .
•
If you cannot turn the hob o after using it, disconnect it from the power
supply.
•
If alphanumeric codes appear on the display when the hob is switched on,
consult the following table for instructions.
DISPLAY CODE
Cookware is detected but it is not
compatible with requested operation.
F0E1
Wrong power cord connection.
F0E7
The control panel switches o because
F0EA
of excessively high temperatures.
The cooking zone turns o when the
F0E9
temperatures are too high.
F0E2, F0E4, F0E6,
Disconnect the hob from the power supply.
F0E8, F0EC, F1E1,
Wait a few seconds then reconnect the hob to the power supply.
F2E1, F6E1, F6E3,
If the problem persists, call the service centre and specify the error code that appears on the display.
F7E5, F7E6
d E
The hob does not switch heat up.
[when the hob is off]
The functions do not come on.
The hob does not allow a special function
to be activated.
e.g.
:
The hob automatically sets a minimum
e.g.
power level to ensure that the cooking
[Power level lower than
zone can be used.
level requested]
DESCRIPTION
The cookware is not well positioned on
the cooking zone, or it is not compatible
with one or more cooking zones.
The power supply connection is not
exactly as indicated in "ELECTRICAL
CONNECTION" paragraph.
The internal temperature of electronic
parts is too high.
The internal temperature of electronic
parts is too high.
DEMO MODE on.
The power regulator limits the power
levels in accordance with the maximum
value set for the hob.
The power regulator limits the power
levels in accordance with the maximum
value set for the hob.
If the iXelium™ logo appears on the glass, the hob has been treated with
iXelium™ technology, an exclusive Whirlpool finish which ensures perfect
cleaning results, as well as keeping the surface of the hob shiny for longer.
To clean iXelium™ hobs, follow these recommendations:
•
Use a soft cloth (micro bre is best) dampened with water or with everyday
glass cleaning detergent.
•
For best results, leave a wet cloth on the glass hob surface for a few minutes.
Please note: The presence of water, liquid spilled from pots or any objects
resting on any of the hob buttons can accidentally activate or deactivate the
control panel lock function.
POSSIBLE CAUSES
SOLUTION
Press On/O
button twice to remove the
F0E1 code and restore the functionality of the
cooking zone. Then, try to use the cookware
with a di erent cooking zone, or use di erent
cookware.
Adjust the power supply connection according
to "ELECTRICAL CONNECTION" paragraph.
Wait for the hob to cool down before using it
again.
Wait until the cooking area has cooled o before
using it again.
Follow the instructions in the "DEMO MODE"
paragraph.
See paragraph "Power management".
See paragraph "Power management".
EN
Publicité
