Milwaukee MS 216 SB Notice Originale page 16

Adapt the feed speed to avoid overheating the blade tips and to
avoid melting plastic materials during cutting.
The insertion tool is sharp-edged and can become hot during use.
WARNING! Danger of cuts and burns
- when handling the insertion tools
- when setting the device down.
Wear protective gloves when handling insertion tools.
LASER
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
Do not point laser at reflective surfaces,
Avoid exposure to laser radiation. Laser may emit hazardous
radiation.
Do not replace the installed laser with a different type.
Any repairs must only be carried out by the authorized service
agent.
GB
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, and plastics.
Stock having a round or irregular cross section (such as firewood) must
not be cut, as it can not be securely held during cutting. When sawing
thin stock layed on edge, a suitable auxilary fence must be used for
firm support.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following ha-
zards may arise in use and the operator should pay special attention
to avoid the following:
• Injury caused by vibration. Hold the product by designated
handles and restrict working time and exposure.
• Exposure to noise can cause hearing injury. Wear ear protection
and limit exposure.
• Injury due to flying debris. Wear eye protection, heavy long
trousers and substancial footwear at all times.
• Inhalation of toxic dusts.
MAINS CONNECTION
Connect only to single-phase AC system voltage as indicated on the rating
plate. It is also possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Appliances used at many different locations including wet room and
open air must be connected via a residual current device (FI, RCD, PRCD)
of 30mA or less.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always lead
the cable away behind you.
Before use check machine, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised Service Agents.
English
26 26
MAINTENANCE
Always disconnect the plug from the socket before carrying out any
work on the machine.
If the replacement of the supply cord is necessary, this has to be
done by the manufacturer or his agent in order to avoid a safety
hazard.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the service
organization.
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnen-
den, Germany.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfills all the relevant provisions of the
directives
2011/65/EU, (EU) 2015/863 (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 62841-1:2015+A11:2022
EN IEC 62841-3-9:2020+A11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN IEC 61000-3-3:2013+A1:2019
EN IEC 63000:2018
Winnenden, 2022-12-12
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that
the product described under „Technical Data" fulfills all the relevant
provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015+A11:2022
BS EN IEC 62841-3-9:2020+A11:2020
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 61000-3-2:2019+A1:2021
BS EN IEC 61000-3-3:2013+A1:2019
BS EN IEC 63000:2018
Winnenden, 2022-12-12
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying out
any work on the machine.
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear gloves!
Always keep hands away from the path of the saw blade.
Never expose tool to rain.
This product contains a class 2 consumer
laser product acc. to
EN 60825-1:2014+A11:2021 and EN 50689:2021.
Do not stare into beam!
Do not dispose of waste electrical and electronic
equipment as unsorted municipal waste. Waste electrical
and electronic equipment must be collected separately.
Waste light sources have to be removed from equipment.
Check with your local authority or retailer for recycling
advice and collection point. According to local regulations
retailers may have an obligation to take back waste
electrical and electronic equipment free of charge. Your
contribution to re-use and recycling of waste electrical
and electronic equipment helps to reduce the demand of
raw materials. Waste electrical and electronic equipment
contain valuable, recyclable materials, which can adverse-
ly impact the environment and the human health, if not
disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
Class II tool. Tool in which protection against electric
shock does not rely on basic insulation only, but in which
additional safety precautions, such as double insulation or
reinforced insulation, are provided. There being no provi-
sion for protective earthing or reliance upon installation
conditions.
V
Voltage
AC Current
n
No-load speed
0
Saw blade dia. x hole dia
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
English
27 27
GB