Publicité
EnGLIsh
•
The DCE571 accepts 300-310 ml cartridges or 400 ml
sausage packs.
•
The DCE580 accepts 300-310 ml cartridges, 400 ml or 600ml
sausage packs.
•
The DCE581 accepts 300-310 ml cartridges, 400 ml or 600ml
sausage packs.
To Change Material Holders (Fig. C)
An alternate material holder is available at extra cost from your
local dealer or authorized service centre. Refer to Accessories for
contact information.
1. Using a screwdriver, remove the screw
plunger
7
from the plunger rod
2. Loosen the material holder from the mounting collar and
remove the material holder.
3. Depress and hold the plunger rod release trigger
the plunger rod completely out from the unit.
4. With plunger rod release trigger depressed, insert new
plunging rod into the unit.
5. Screw the new material holder into the mounting collar.
6. Install screw through the plunger onto the end of the
plunging rod.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Refer to Fig D.
Variable Speed Dial (Fig. E)
The material's rate of flow is controlled by the variable speed
dial
3
to accomodate various applications.
•
Pick a speed by turning the dial to the desired setting.
nOTE: '1' is the lowest (slowest) setting and '6' is the highest
(fastest) setting.
Variable Speed Trigger (Fig. F)
In addition to the variable speed dial, the material's rate of flow
is also controlled with a variable speed trigger.
1. Squeeze the trigger switch
nOTE: The further the trigger is depressed the faster the
rate of flow.
2. Release the trigger switch to turn the tool off.
32
17
and separate the
5
.
6
and pull
1
to turn the tool on.
Trigger Switch Lock-off (Fig. F)
Your tool is equipped with a trigger switch lock-off
safeguard against inadvertent release of material.
1. To lock the trigger switch, push trigger switch lock-off
up. The tool will not operate with the switch in the
locked position.
2. To unlock the trigger switch, push the trigger switch lock-
off down.
Rotating Cartridge Holder (Fig. G)
The cartridge holder
8
rotates 360˚ to apply material at
any angle.
Plunger Rod Handle (Fig. A)
WARNING: To reduce the risk of serious personal
injury, DO NOT use the plunger rod handle as a hook to
suspend objects from.
The plunger rod handle
4
stable location when not in use or for storage.
To Adjust Plunger Rod (Fig. A)
1. To manually adjust plunger rod
plunger rod release trigger
2. Push or pull plunger rod handle
3. Release plunger rod release trigger.
To Insert Material
Cartridge Holder (Fig. A, I)
1. Ensure that plunger used is appropriate to material.
nOTE: Using incorrect plunger may result in material
container exploding during use, damaging cartridge holder
and/or caulk gun.
2. Use the trigger switch lock-off
3. Trim nozzle end of the caulk/material tube (Fig. I). Small
openings require more force to push the material possibly
affecting battery life.
4. Break inner seal of caulking tube or material using the
poker
9
located on the under side of the cartridge holder.
NOTICE: If the inner seal is not broken, material could
be forced out through the rear of the tube and damage
the tool.
NOTICE: Keep plunger rod, cartridge holder and cartridge
clean of all material. Retracting a plunger rod that is
covered with dried material may damage the internal
parts of the tool and cause misalignment of tube.
5. Securely hold the tool, press plunger rod release trigger
to declutch and free the plunger rod
rod handle
4
, pull the plunger rod back to allow the caulk/
material tube to fit inside the cartridge holder.
6. Insert caulk/material tube.
7. Press and hold plunger rod release trigger
the plunger rod handle
against the tube.
8. Release the plunger rod release trigger.
9. Rotate cartridge holder to desired angle.
2
may be used to suspend tool from a
5
, press and hold the
6
.
4
to desirable position.
2
to lock trigger switch
5
. Using the plunger
6
while pushing
4
forward until the plunger
to
2
1
.
6
7
is
Publicité
